Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

My dishwasher filter keeps getting plug up with large food particles. I take it apart and clean the screen. It works for a 2-3 -4 weeks before I have to do it again. There is a spinning fan on the screen. I'm wondering if this scrapper fan is working at all. If it was I think it would keep the small screen free from particles. The first thing that happens is the top cleaning arm stops working.' Thanks


Answers :

Hi Judy. The only way to know for sure is to power up the fan independent of the machine and see if it still works. In the meantime, rinse and remove all debris from the dishes prior to placing them in the machine, including pots and pans.
\015\012
\015\012This method will give you much more sanitary washing either way. Also, always run the hot water into the kitchen sink until it is hot before you push start on your dishwasher. Joe
Before the plates or dishes are put into the washer the larger food remaining must be removed/cleaned or wiped off so that you will not have the filters gettingg clogged often.
\015\012The scavenger fan must work to push off all the dirt into the filters after it is pulverised.
\015\012Make sure that there are no dirt accumulation, use a good air jet/water jet to clean the filters and the fan for the free movement. You can also make sure if the fan connection to the controller is working fine.make sure the connectors are tight , if not the controller can be faulty.
\015\012Finally this seems not a serious issue if you can be a little careful to clean the washer often so as to prevent accumulation of larger food particles.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher filter keeps getting plug up with large food particles. I take it apart and clean the screen. It works for a 2-3 -4 weeks before I have to do it again. There is a spinning fan on the screen. I'm wondering if this scrapper fan is working at all. If it was I think it would keep the small screen free from particles. The first thing that happens is the top cleaning arm stops working.' Thanks


Hi Judy. The only way to know for sure is to power up the fan independent of the machine and see if it still works. In the meantime, rinse and remove all debris from the dishes prior to placing them in the machine, including pots and pans. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

Hi - I've been all over your web site and keep getting rejected - alas. I have one of those wonderful Fisher Paykell double drawer dishwasher unit Model # 88445 (I think but also see another number LIM725367) I bought in new in 2007 worked fantastic but tore down my b ungalow now have a new kitchen ready for it. Carol 303 320 1697 [email protected] May 6 2011 11:30 AM MDT I would like to obtain an installation manual so I can make sure I packed all the parts and then put it in m


Hello Carol - \015\012\015\012\015\012The full model number for future reference is DD603-88445. I've uploaded the installation manual for all Fisher & Paykel DD603 double-drawer dishwashers to Rapidshare. Please follow the instruc ... Dishwashers

A GE triton dishwasher causes hammer noise when stops filling. The sink faucet works fine as do all the other faucets in the house. I cleaned all of the traps in the dishwasher. Because the sink works, I don't think it is a sink valve problem. I turned off the water to the house and drained the system, the air chambers should be good. Is there some component of the dishwasher that could be causing the noise? Would cleaning the pump help? If so, how would I do that?


The cause of the hammering noise, (slamming) is due to the water inlet valve on the Dishwasher (DW) shutting off abrutly once the DW reaches the proper amount of water.\015\012\015\012If this is an older DW, you might want to replace the ... GE Dishwashers

I have a Quiet Guard Standard model #587.151524 that is not cleaning the dishes. I took the bottom spray arm and screens out and cleaned them, (they had a heavy buildup of what I would say is calcium. The arm cleaned up fine but the screen still has some areas that will not allow the water to drain. I tried CLR and it helped but the screen is still probably 60% clogged. Do you think this is the problem getting the dishes clean and if so do you have any suggestions about how to clean the screen?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Kenmore 24 in. 15689 Built-in Dishwasher

I think I am finding small pieces of the wrap from the tablets in the small holes in the spray arms, one wont move anymore??? This is about 10 yr old maytag machine. I tried to clean out the spray arms but dont really know what I am doing. Bought a new diswasher, dont want to use the tablets if they will clog up the works. please advise.


Just prime the sink before you start the dish washer ... Maytag Jetclean II MDB8551A Dishwasher

I borrowed my friends pressure washer and it was working when i had it but she says its not now, could u tell me what u think it could be please. Could it be a motor problem and if so can u explain how a motor would go without me touching it as i dont like the idea im being acussed of breaking it when it was working when i gave it back


The water has emptied out of the machine in transport you may have to bleed the air out of the pump ... DeVilbiss Pressure Washer Hose 25' 38" Id Rubber Has

I have a linea dishwasher model LDW 3SS i think it is about 3 years old , it used to start but not complete the cycle just stop halfway and then would only work if you slammed the door or pushed front of machine and now it wont work at all ???


Even though this is an old issue, I thought it would be good to close out.\015\012\015\012I had the same issue where the dishwasher would stop at two certain point in the program. If I'd manually advance past that point, it would keep goi ... Dishwashers

Judging from the information on this forum and others, we think we need to replace the control module on our Bosch dishwasher (she45m05uc/50). The general consensus seems to be that the module has an underrated relay and will burn out again. Has the board been redesigned? Is there a newer board that would work in our model? Bosch says that only part number 676962 will work. Thanks for your help, Deb


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

I have a bosch shv99a13uc. i rescued this from a thrift store so i am not sure of the history . i have installed it . all the controls work . it fills and trys to work it dosen't spray much and grinds like a very loud timer what tests should i do and can i get a manual that shows me ho to get the pump out. I think it sounds like something in the pump any help would be great Thanks


Hello &\015\012Welcome to FixYa\015\012\015\012Please check\015\012this video on how to clean the pump filter:\015\012\015\012 ... Bosch 24 in. SHV99A13UC Dishwasher

Not working the soap dispenser is not working batteries got all wet and brown and green I think a soap dispenser should be made to to get water in where batteries go I would like a new one or my money back very unhappy.... angela muir,16 n. steele st.,worcester,ma 01607 email [email protected]


... Dishwashers

THe ProScrub light is steady, and the dishwasher does not work. When I push buttons, the light keeps going off, and with the next button push, it goes on. If I leave the dishwasher like this for a while, then a couple of the other lights, I think the Normal and Heated Dry lights will blink continuously. In either state, the dishwasher does not work.


... KitchenAid 24 in. KUDS02FR Built-in Dishwasher

My bosch shu43c02uc wont work at all and i think i need to reset it, how would you reset it and can you think of anything else that will help with the problem?


Hello\015\012 \015\012Welcome to Fixya.Based on your post,"my bosch shu43c02uc wont work at all..."\015\012 ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Cancel wash working fine. when ready to wash get humming sound. pumpmotor not turning. A glass dish broke a week ago and work fine till know remove screen today found some small brokeb glass - like when a harden glass brakes? if something is in the pump how do i remove pump


In\015\012most dishwashers, the water pump is located under the lower sprayer\015\012arm. This component pumps the water through the dishwasher. The pump\015\012has two impellers, top and bottom. These, as well as other components,\015\012can become ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app


... Karcher 1550PSI Pressure Washer

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

No water The serial number is not my dishwahser, however mine is about 6+ years old and has worked fine, I keep it in fairly good order, cleaning rotar arms weekly and filters as often as needed. Yesterday 4th August the timer which is a dial type, was getting as far as the next section and stopping, also it would seem that no water is being drawn through the arms. Are we near the end of life or is it fixable?????


Check first the filters on the inlet water line.\015\012Then, if problem still exist - check that the inlet water valve works(it is an electromagnet valve, located at the pipe's entrance to the machine)).\015\012If it doesn't work, test that it get ... Neff 24 in. S5409X0 Built-in Dishwasher

White Whirlpool dish washer. Works great except when it leaks, there appears to be a small hole in the tub. Is there an inexpensive fix or would it need a new tub?


Some dishwashers have a long warranty on the tub , check it out before doing anything to it. If it turns out that there is no warranty go to your local marine shop and ask for marine tech epoxy, it is very strong, water proof and can stand hig ... Dishwashers

I have an F2 error and the fan or dryer keeps running...i understand that this means a high water level and i have already checked the screens and filters. but how do i turn off the dryer so i may safely inspect the pump and drainage system?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Sorry you have had to wait so long for a reply, it seems there are only a limited number of techs here familiar with Asko. Anyway, yes F2 normally would indicate a hi water level detected...norma ... Asko D1776 Built-in Dishwasher

Middle and top spinners do not spin The pump is pushing water up the back delivery tube. There are no dishes in the unit and I was able to trick the door into thinking it was closed so I could watch what was happening. Or Not Happening The spinners are completely free of calcium or soap build up and both top and middle are easily spun with a finger. While the pump and bottom spinner were working, I pulled the top drawer out partially and there appeared to be a good flow of water coming out of


Hi,\015\012 Remove each spray arm and check it is clear of food particlesat the jets. The next problem may occour at the rotating joint . If the seal is not good, you can loose a lot of water out of this point.. If both of these seem reasonable ... Dishwashers

My son and daughter in law bought a new home with all ge appliances and the dishwasher is americana. the dishwasher from the start has never worked properly. the water is cold and the drying cycle doesn't heat up. also, it doesn't drain completely. I think that this dishwasher should be repaired or replaced free of charge.


I agree, especially if it is less than 1 year old. See if the builder of the house will make arrangements for repair or replacement under his guarantee. If not then try the store or company that supplied the dishwasher. If the appliance was registe ... Maytag Dishwasher

Design Flaw I had the same problem. While under warranty they "fixed" the problem by putting in a zip tie (no joke) to keep top spray arm from rattling. The tech said they were working on a resolution of the design flaw. Then, when the zip tie broke I called them again. This time they replaced a small o-ring where the water line comes into the top spray arm. The o-ring eventually fell off. When that came out for the 3rd time, they re-ordered the same o-ring. Now again, I am having problems with


... GE 24 in. GSD2120C Built-in Dishwasher

Low pressure I have dewalt 3800 pressure washer and it went from working fine to a bit more pressure than a garden hose. The screen is clear at the water intake witch leads me to think it's the cat pump,but how do i know.


Hi\015\012some valves at cat pumps need a 100 psi pressure to open and close correct.\015\012when there is air in the pump the valves wil not open and close till air is bleeded.\015\012take of highpressure hose, open watertap and bleed pump till no ... Dewalt 3800 PSI Pressure Washer

Our KitchenAid Superba model KUDS01DJss0 ( about 7 years old and has always worked fine) I think is not heating . . the dishes come out wet and don't seem very clean if they had especially if they have a small a bit of something like peanut butter on them when loaded ( so lately I've been dong a pre-wash by hand). Unit doesn't seem to get very "hot" during the wash/dry and steam does not billow out when I open the door soon after the cycle completes like it used to. It does feel warm to the


Hello. The new heating element will come with a new control board. There are no tricks to the change actually, the easiest way to change the heating element is to unhook the plumbing, electrical, and drain hose then pull it out and get to the back ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0973 seconds