Having problems with your KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher ?

Wont run I have power to the unit but it wont run i have no lights on the unit


Answers :

If your dishwasher doesn't work at all, check these:

Power from the house
Door switch
Wiring
Timer or selector switch
\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is there power getting to the dishwasher? This can be difficult to test, because dishwashers are usually wired directly to an electrical circuit, rather than plugged into the wall. But at least check for a blown fuse or a tripped circuit breaker.

\015\012\015\012\015\012\015\012Door switch\015\012\015\012The door switch is important because, if it's defective, the dishwasher won't work at all. To reach it, you need to remove the control panel cover, or sometimes the interior liner of the door. If it's defective, you need to completely replace it.

\015\012\015\012\015\012\015\012Wiring\015\012\015\012Often the main wiring connection from the house, at the dishwasher, burns and breaks the connection. If that's the problem, the wires must be repaired/replaced as necessary. If that's not the problem, check the wiring to the door switch, the wiring between the door and the lower part of the dishwasher, and the wiring to the timer. Repair any broken, burned, brittle, or defective wiring, using the proper appliance-grade wire and connectors.

\015\012\015\012\015\012\015\012Timer or selector switch\015\012\015\012Although it's uncommon, the timer or the selector switch may be defective. If so, you need to replace the defective part, because neither of these can be repaired.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wont run I have power to the unit but it wont run i have no lights on the unit


If your dishwasher doesn't work at all, check these:Power from the house ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

My GE 24 in Profile PDW8280JSS door wont open: Now the "clean" light is on. I tried cutting power for over an hour, I have run wash cycles, the lock handle will not move. The unit did not have much in it, when I last closed it, so I don't think it is jammed. Any ideas?


Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence: ... Dishwashers

Kenmore Ultra Wash Model 665.15801891 (Serial FJ3403697). This is in the USA. Unit will not run. Two lights are lit on the display panel and do not go off - 'Drying' and the #2 on 'Delay Hours'.rn I have turned off the power at the breaker box hoping it would reset. Once power is turned back on the Lock light comes on. I can clear that by pressing 'No Heat Dry' for 4 seconds but then the 2 lights mentioned above come on and do not go off. Any suggestions? Can you tell how old the unit is by t


Plase confirm if your model has the same front panel as the one shown in this manual.\015\012In that case try this sequence to reset the dis ... Kenmore 15899 Built-in Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Came home and dishwasher was stil running from the morning. Opened the door and all the lights on the control panel were lit up and unresponsive. cut power to unit for 1 min and now the controls don;t light or respond to anything . They are not locked and there is power to the unit any ideas ?


Hi\015\012\015\012\015\012Thanks for using FixYa. From what you have described it seems that the control panel has gone bad and needs to be replaced however, if you want more information then please do revert with the manufac ... Dishwashers

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Brand new haier hdc1804tw wont start. i press the power button unit beeps once and power light comes on but i cannot select cycles. unit will then beep every five minutes. i have made sure there's water and unit is level. i have left it unplugged for over five minutes with same resulting issue.


... Haier HDC1804TW Dishwasher

I have a KitchenAid dishwasher model#KUDC25CH.The problem that I am having is the touchpad control panel all of a sudden is lit up like a Christmas tree. Just about every red indicater light is lit. The DW will run but I dont know what kind of wash it is performing or at what stage the cylce is in. I have tried canceling the cycle,I have tried child lock/unlock,I have cut the power to the unit for a few minutes hoping the computer panel would reset itself. I am affraid to run the unit in fear th


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

We lost power as our dishwasher was running. When power was restored it seems to be stuck in the drain cycle. We have tried turning the unit off and back on and also holding the start button for 5 seconds.The 4 lefthand lights blink on and off and the right hand lights are steady. It is a model D1996.


Try to unplug it or turn off the circuit at the electric box.............wait ten minutes or so and plug it in and try again..................the program needs to be reset in that manner sometimes....... ... Dishwashers

DISHWASHER WAS IN MIDDLE OF CYCLE... HOUSE LOST POWER AND NOW WASHER STOPPED AND WONT FINISH CYCLE NO LIGHTS ON BOARD DOES HAVE POWER TO UNIT HOWEVER NOTHING LIGHTS UP


Remove the rear panel. Gain access to the thermal fuse. (glass tube like fuse)\015\012This does have a tendency to go bad. A faulty door switch can also cause this. ... Kenmore Dishwashers

Kitchen circut was accidently turned off. Now whirlpool gold disher will not work(unit was not running and the door was not closed all the way when circuit was turned off, All circuit breakers are on) There are no lights on display when door is closed completely, and it appears to have no power. Worked fine prior, what could it be? The unit has not been removed from under the counter yet. Is there a fuse or circuit breaker on the unit? If so where is it located? Other troubleshooting ideas


Hello- Turn power off. Remove kick panel and cover for power wires. Check connections. If these are ok, most likely suspect is a fuse at the control. This is a little harder to get to. Remove inside door panel screws. Unplug wires and remove panel. F ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have just bought a Kenwood KID60S10 dishwasher. I have used it a couple of times with no problem. However I realised it has been leaking from the water pipe at the back so pulled the unit out to tighten and readjust the pipe. However when I tried to run a cycle it won't after this to check if it was still leaking it won't. When I choose a programme non of the lights light up (except the power on/off light). I had left the washer out of the cavity to ensure the pipe wasn't leaking anymore. It i


... Dishwashers

AFTER RUNNING MY DISH WASHER I OPENED THE DOOR THERE WAS ST HALF IN OF WATER IN THE BOTTOM SO I WAS GOING TO WASH AGAIN BUT HAD NO LIGHTS ON CONTROL PANEL HAD POWER TO THE DISH WASHER BUT NOTHING WOULD LIGHT UP? DONT HAVE 10 WASHES WITH THIS UNIT .? MODEL #655-13443K900


Hi Bennie, Try http://www.manualowl.com for free PDF for troubleshooting the issue you are having. I hope this helps. ... Kenmore Dishwashers

We have a 6 year old Jenn Air dishwasher model JDB2150AWP We had a cracked door close unit which we replaced but got a short while restoring connections I am wondering if there is an internal circuit breaker, relay or fuse on these machines that we need to check and possibly replace since we cannot get it to run at all. No power or lights at all. I believe all connections are secure and we replaced the door close unit with new parts.


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

The "clean light" on our Kitchenaid KUDIO1FLSS flashes 7 times and I cannot clear the problem to allow the unit to operate. Is there a sequence, using the control buttons, to permit the unit to run a system check? I disconnected the power for 30 minutes but that did not solve the problem.


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Lost Power We always run the unit before bed on the delay timer. I heard it kick on last night. When we woke up this morning I first noticed that the clean light wasn't on. Then I noticed that the dishes were still very damp. Lastly it has about a inch of water laying in the bottom of it. It appears that it just lost power during the cycle. What are some areas I may trouble shoot before calling in a repair person. Thanks


Replace the thermal fuse inside the control panel.\015\012Part #3376359 ... Whirlpool DU960PW Dishwasher

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

Clean light flashing and unit wont run


You can open the lowe racess panel of d/w and you find a techsheet/ trouble shooter, in ther they will explain how to reset a clean light blinkin 7 times.. you can try pushing the "sani-rinse"---"heated dry"--- "sani-rinse" --- "heated dry"... toggli ... Whirlpool Dishwashers

Opened door and unit did not have electrical power (lights did not come on either unit). Called serviceman. He stated there was no electricity to unit(s). Called electrican. He stated wiring to the dishwasher had power. Called serviceman again. He came out and dishwasher worked. He did nothing to it. I opened the door and the lights(buttons) came on. Unit worked for a few days and this morning, there was again, no power to the unit. What is likely wrong with this dishwasher?


... Fisher DD603B / DD603W / DD603H Dishwasher

Dishwasher won't run. Replaced door latch and timer/selector unit. Into this POS for over 200 bucks right now, with nil result. Any other ideas? Clean light comes on so power is getting through it.


If it's KitchenAid or Whirlpool or Kenmore, and your clean light BLINKS and the heating element inside is ROUND - there is a problem with your control board and the element. There is a kit containing both, for the price of the heating element alone. ... Dishwashers

FDB520RHS2 Dishwasher Same problem as posted. Dishwasher has power & water - control panel lights are on, when start is pressed the sound of a relay can be heard but nothing else happens - no water fill no cycle. Unit stays in this condition without running.


... Frigidaire FDB520RHS Full Console Dishwasher with 4 Wash Cycles 4 Wash Lev

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0927 seconds