Having problems with your KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher ?

My dishwasher has no power . I had work done on the floor which caused vibrations. My water connection was leaking which I fixed but I found out that It has not power. Not sure if the vibration caused some wires to disconnect. What should I check before I pay $130 for a repair man to diagnose the problem.


Answers :

Call the technician. Have him state on the bill that whoever did your floor caused the electrical malfunction
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher has no power . I had work done on the floor which caused vibrations. My water connection was leaking which I fixed but I found out that It has not power. Not sure if the vibration caused some wires to disconnect. What should I check before I pay $130 for a repair man to diagnose the problem.


Call the technician. Have him state on the bill that whoever did your floor caused the electrical malfunction ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Completely dead. breaker is fine. have live power at dishwasher. ???? Replaced heater, pump and check valve last year. No obvious burnt or disconnected wires.


There is a thermal fuse located behind the operator console on nearly all Kenmore or Whirlpool manufactured dishwashers. There were some noted problems with certain model dishwashers where the wire gauge on the thermal fuse was too small and would he ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Woke up this morning and the unit acts as if it has no power. no lights, no sounds, nothing. I checked the power and it has power. I checked the wire nuts in the box with the power coming in and they are fine...it is only 1 and a half years old...Please help.


... Haier ESD311 24 in. Built-in Dishwasher

The unit is a Maytag model MDB5601AWW which it has recently began to lose power at the touch pad. The electrical breaker has been checked to confirm normal voltage. Additional investigation suggests that the unit can be reset by (1) disconnecting the power at the breaker, (2) disconnecting and reconnecting the ribbon cable that interfaces the touchpad with the control board. However, the problem reoccurs after a few normal wash cycles.


It sounds to me then that the display board or touchpad needs replacing,you havn't said that it's not doing it's cycles.so it's not causing any washing or cycle problems.i would replace the display board. ... Dishwashers

I have a Kitchenaid model KUDL02IRBS1 dishwasher. It died with no lights to the front panel at all. I have power at the main wire connection to the unit. I checked the door switch and it works. I checked power at what looks like a solinoid on the circut board and it has 115V.


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Hobart LXIC under counter comerical dishwasher. Delime lled keeps comeing on every time power up. Checked sensors on bottom in the water drain area senser on right (there are 2 next to each other on this unit I think other is water temp) the wire had wire burn completely off. I reconnected the wire and started to burn up the wire again. Question: 1) Is this sensor for the Delime sensor? 2) does it sond like the sensor is shorted to you? or sending wrong voltage to sensor? 3) If no


... Hobart 24 in. LXIC-5 Built-in Dishwasher

I have a whirlpool dishwasher model# du943pwkqo. What wires go to the thermal fuse? I lost power to it and took it apart to check the fuse and there are no wires hooked up to it. Does any one have a wiring diagram?


It is a black wire from the door switch.. hope it helps the tech sheet \015\012\015\012http://www.servicematters.com/docs/w ... Dishwashers

We have a service contract with Broward Factory Service. My GE dishwaher went out with eater in it, no power. Checked the panel box flipped switch, nothing. The service tech. said the rinse aid cup leaked and ate thru the wiring, and he had read a recall about this. I am checking to see if Model #GSD3610Z00AA, Serial #ZS782757B is on the recall list.


I was trying to find out if the dishwasher was on a recall list, and I did by calling GE direct. It was not, so the service I have is replacing the rinse aid box.\015\012Thank you, ... GE Dishwashers

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

De Dietrich Dishwasher - DVH 610 JUI - when turned on to any programme and started automatically tries to drain water instead of filling with water. Was disconnected and filters checked and were clean. when turned on again it worked and when disconnected to be brought back into house it again tried to drain water instead of filling. All lights come on except blue light. Does not accept engineer code given with wiring leaflet


... Dishwashers

Kenmore 13599K600 stopped working. Panel board doesn't respond - no lights, no response. Power getting to unit... checked at hard wire ends behind kick plate panel and power is reaching the unit.


Had the same issue and had to replace both the board and the fuse. Six months later, same issue again. It might be when the "Sani Rinse" is used as it dies at the end with some water left but the water is very clean. Possible defect? ... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

My kenmore dishwasher has no power. No lights come on - nothing. I checked the wiring running to the machine, and it has power. Just not coming on


... Kenmore 24 in. 16032 Built-in Dishwasher

Whirlpool Undercounter Dishwasher DU8900XY1, My dishwasher is dead. It stopped in the middle of the wash cycle and has not operated since. I checked the power at the junction box and power was confirmed. I could not see or smell any burnt wires. I don't know the next thing to trouble shoot to fix the problem. Please help


Take off the kick panel and open up the j-box at the dishwasher only. Just make sure there is no burned wire nut or loose one\012\012Thanks ... Whirlpool Dishwashers

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

I purchased a used Dishwasher KUDE70FVSS but it will not power on. I have checked the power up to the control panel. An earlier posting said to replace the thermal fuse. I don't have a wiring diagram so I don't know where to locate it or what it looks like. Thanks David


HI. This is true. There is a thermal fuse that will burn out under adverse conditions. This could be a power surge or element failure. This fuse is mounted in close proximity to the main board. Both parts are housed within the control panel. The actu ... KitchenAid Dishwashers

I got this dishwasher from a friend that had mice chew the hoses and i was told that it worked perfect before the mice chewed it. I replaced the drain and fill hoses plus the power cord. when i put everything back together and power on I get F1 on the top drawer and the rotor rotates and the heater plate turns on. The botton drawer does nothing with no display. I checked all the wires with a meter and found good continuity thru every pin. I replaced the main filter board. I even switched the


Did the F1 error in the top drawer disappear after you replaced the mains filter board? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Hi. I have a 3 year old LG dishwasher. It will not drain. Display shows OE. I completely cleaned the drain assembly inside the DW. I checked the discharge line, it is completely clean. I disconnected the drain line from the air vent assembly at the sink and ran the DW, still will not drain. I disconnected the discharge pump wires and ran current directly, the pump works. I replaced the main control PCB, still will not drain. Please advise. Thanks


Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.\015\012\015\012Please reply with what worked best. Thanks! ... LG 24 in. LDF 7811 Built-in Dishwasher

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

LG dishwasher quit mid cycle. no power to the front panel. I drained the water and found a two pronged wire by the drain hose disconnected. reconnected it and I still get no power on the control panel


Here is the video for you its intresting to get it repaired V ... LG Dishwashers

Dishwasher appears to have no power - no panel lights at all (lock, start, etc). Power is 120VAC at outlet to DW when disconnected but the voltage is 60VAC at junction box under DW once it connected. Acts like a floating ground but N is 0VAC to Grnd. ??? what should I be testing / checking??


Door switch ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

My wife and I just moved into our house and cannot get anything on the dishwasher to activate. We have checked fuses, lightswitches that might be wired to DW power -- nothing has worked. Is there a universal power switch I am missing?


Sounds like a power supply issue. Take off the lower panels below the door and look to the right side of the opening, you will see a little square steel cover. This cover is where your power comes into the dishwasher. Follow the line coming into the ... Whirlpool DU930PWS Built-in Dishwasher

Indesit d41 dishwasher overfilling, pressure switch seems ok(checked with multimeter) ,when pressure switch is manually operated the electro fill valve remains open. only time fill vave shuts is when power is off or door is open. can someone please help as i cant find wiring diagram or service guide online


Possible faulty pressure switch or a faulty drain pump ... Indesit 18 in. D41 Slim-Line Free-standing Dishwasher

Maytag MDB6600AWW Unit is approx 3 years old it was finishing a load and stopped part way through sticking on heated dry. I don't know if it was there in the cycle or if the diagnostics on the board sent the message there. The light now will not shut off or move from the heated dry. I have disconnected 120 volts, removed the panel to check wiring, removed board and reassembled nothing resets the heated dry light and nothing works. I have gone through manual function test, sales floor demo test,


Have you tried pushing heated wash, heated dry, heated wash then heated dry? Sometimes this will reset it. ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0685 seconds