Having problems with your KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher ?

In order to reset my dishwasher i was told to alternatively press the clean and rinse button. my dishwasher has no button that says clean, rinse, or clean and rinse. my button choices are as follows: Front: CANCEL and START/RESUME Cycles: HEAVY DUTY, NORMAL, LIGHT/CHINA, QUICK CLEANUP, or RINSE ONLY Options: PROSCRUB, HI-TEMP SCRUB, SANI RINSE, HEAT DRY/Lock symbol, 4 HOUR DELAY. Does anyone have the correct sequence for initiating the diagnostic cycle?


Answers :

If you want to reset the computer in that dishwasher you can just unplug it for a half hour. if it is a built in just locate the fuse in the or breaker that the dishwasher is on and pull it for that length of time.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

In order to reset my dishwasher i was told to alternatively press the clean and rinse button. my dishwasher has no button that says clean, rinse, or clean and rinse. my button choices are as follows: Front: CANCEL and START/RESUME Cycles: HEAVY DUTY, NORMAL, LIGHT/CHINA, QUICK CLEANUP, or RINSE ONLY Options: PROSCRUB, HI-TEMP SCRUB, SANI RINSE, HEAT DRY/Lock symbol, 4 HOUR DELAY. Does anyone have the correct sequence for initiating the diagnostic cycle?


If you want to reset the computer in that dishwasher you can just unplug it for a half hour. if it is a built in just locate the fuse in the or breaker that the dishwasher is on and pull it for that length of time. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

Kitchen Aid Dishwasher - model: KUDPO2CRBLOrn Ran the dishwasher twice on pots/pans cycle and sani rinse with a special cleaner recommended due to build up and items not getting clean. (soap left all over them) Cleaned machine out great! Now, the only choices that will light are "quick clean up" and "rinse only." Even if I choose them, when I hit the "start" button - the machine will not start. No other lights will light. Machine will not start. Any ideas?? Thank you!!!


... KitchenAid Dishwashers

My dishwasher worked just fine yesterday afternoon. I loaded the dishwasher again after dinner and tried to start it, but I got no response from the buttons on the left side of the panel. The buttons on the right side (hi temp scrub, sani rinse, and air dry) light but don't do anything. I also get no response from the delay hours, start, or cancel buttons. Help?


... Kenmore 24 in. 16939 Built-in Dishwasher

I have a whirlpool quiet partner i dishwasher (model DU1055XTSQ2) that has suddenly stopped working. Control panel has partial functionality. All of the buttons on the control panel have a green LED feedback light when depressed. None of them provide LED feedback anymore except the Hi-Temp Wash, Sani-Rinse, and Heated Dry buttons. So there is power to the dishwasher. Any ideas? Please help Scott


The control board has failed.CLICK HERE to see the parts breakdown. ... Whirlpool DU1055XTSQ Built-in Dishwasher

Kenmore dishwasher 665.13843K601 ser. FU4806977 STOCK 13843K TYPE 575-0 Tried to turn it on won't start/ run/ perform any functions The following buttons light up but will not perform functions; Smart wash and heated dry also lights up like it should, pots and pans, normal, fast wash, high temp, sani rinse The following buttons do not perform functions or light up Quick rinse, Turbo ZOne, Delay Hrs., Cancel/Drain, Start/Resume I killed the power to it for 1 minute for reset but d


The touch pad is not working. Pull the front kick plate from font/bottom of machine and there is a 'TECH SHEET'. This has a complete diagnostic sequence for you to go through and verify the functions for you. ... Dishwashers

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

My KitchenAid model number KUDSO2FR-SS hs blinking lights that won't shut off. The Pro Scrub light blinks on and off and won't shut off. I can sometime lock it out with the heat button but it lights right back up. After a couple of minutes the normal button starts blinking as well as the clean button. The dishwasher does not turn on. I tried unplugging it but it just reverts back to the same thing


... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

I have a whirlpool gold quiet partner 3 n the cancel button won't go off n the normal wash button won't go off either. I can do a quick wash cycle on it but then goes right to sani rinse afterward n don't shut off itself it just keeps on going. Solution? Is there a reset for it because I have an air dry button but not a heated dry button so I don't kno if I should push sani rinse/air dry two times over as opposed to sani rinse/ heated dry or if there's a diffrent solution for it. This all starte


... Dishwashers

I have a whirlpool du1055xtsq3 dishwasher that is partially working. Cycle buttons light up but start button does not. I've tried resetting by pushing sani-rinse and heated dry alternately. Control panel lit up and heard motor running but no water. Your help is appreciated. Unit only 2yrs old. Thanks!


... Whirlpool Dishwashers

Kenmore Model 665.1703 clean light flashing. toggles sani-rinse and heated dry buttons. turned on but motor not spinning. Motor or start capacitor?


... Kenmore 24 in. 17032 Built-in Dishwasher

The sani-rinse and hi temp scrub options do not come on when i push the buttons on my kitchen aid dishwasher model number is kudk03ftss0


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Non-starting unit The dishwasher will not start, reacting as if the door is not closed. The right side of the control panel (air dry, sani rinse, hi-temp scrub) allow selection i.e. the indicator light comes on. However, none of the cycle selection buttons on the left will engage.


... Kenmore 24 in. 16934 Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

My dishwasher is only one and half year old. all of a sudden the dishes seem not be rinsed properly. As if a small coat of thick unrinsed film further stick on thedishes and glasses after the drying cycle I then have to proceed to scrub each dish ,fork, knife and glass... I cleaned the dishwasher with a special product t to clean the empty dishwasher, and the drying rinse agent is on full . Please advise


Try running a cycle with bleach on an empty dishwasher water might be too soft ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have the same green clean light flashing problem but with model KUDE40FXW, which has the two control panels. I've tried the Sani-Rinse, Heated, Sani-RInse, Heated sequence and nothing happens.


... KitchenAid KUDE40FXWH Builtin Dishwasher

Kitchenaide dishwasher #KUDP02CRBS2 --- all lights on the panel are lit up. I pressed the sequence "sani rinse - heat dry- sani rinse - heat dry". What now? Thanks in advance


... KitchenAid 24 in. KUDP02CRBS Stainless Steel Built-in Dishwasher

Model no. MDB6100AWW. Just unloaded the dishwasher. Shut the door and immediately heard clicking (regular cadence). All indicator lights (arrow-shaped) for clean, dry, wash and heating delay were blinking. Opened the door, waited a few minutes, closed the door. Now, just the "Clean" and "6 Hour" arrow indicator lights and "Heated Dry" button light indicator are still blinking continuously. Cannot override. What's going on? Dishwasher came with the house when we purchased it 6 years ago. Proba


Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash-heated dry ... Maytag 24 in. MDB6100A Built-in Dishwasher

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Bosch Dishwasher I currently own a Bosch dishwasher. One of the selling points, if I'm remembering right, of the dishwasher was it was supposed to super heat the hot water that is coming in from the tap. I have 3 problems. We have to rinse the dishes by hand before putting them in the dishwasher, Otherwise they won't come out clean. The dishwasher will run for four hours sometimes longer. It doesn't seem like it is heating the water any hotter than what comes out of the tap.


Your control board is bad. ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?


... Maytag Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2260 seconds