Having problems with your LG LDF6810 Built-in Dishwasher ?

Our LG 6810 dishwasher has stopped cleaning. After the cycle the dishes are wet and covered in greasy clumps. We ran the test cycle and got the following: 3H/U3 11 22 33 44 55 66 04-2 32 33 0 (inlet valve) 35 36 37 38 23 (Thermistor) 3A 3A (beeped twice and showed 3A) 3A (beeped twice and showed 3A) Any advice you could give me would be appreciated. I have the service manual but have never done any type of dishwasher repair. I'd like to not have to replace this dis


Answers :

1.) Take racks out of unit.
2.) put both of the spray arms in the 12 o'clock position
3.) Run the washer,once the washer has started wash cycle,open the door and ensure the spray arms have moved off of the 12 o'clock position. Write down results.Also write down the amount of water that is in the tub.
4.) On the drain/pump filter take off the top four pieces as shown on the diagram pg.28 of the service manual.Look for large pieces of debris. Fill tub up with water then cancel/drain.
Note and write down how much water is in tub after draining.

This procedure will allow us to isolate the issue.
It could be one or some of the following.
1.)drain clogged or drain motor defected.
2.) Wash pump defected or filter clogged.
3.) Spray arms clogged.

Please post results.
Thanks.....
Keith
Without going into the results of the test cycle, try the following two procedures. The may still be water residue at the bottom of your machine. If the machine is not fully drained it picks up some of the residue and sprays that onto the dishes during the final rinse, leaving an unhealthy and unsightly film on everything.\015\012
\015\012Remove the bottom strainers plates and make sure that the outlet pipe is not kinked, that there is nothing obstructing the pipe or the pump or selector valve. If possible back flush through the outlet pipe and try draining the machine once more before using it again.\015\012
\015\012Check that the arms spin freely when spun by hand, then check the outlet jets at the trailing end of the arms are not blocked with food particles and other solid matter. This often happens and the arm is unable to turn because the water jet that is supposed to drive the arm does not have the force to rotate it with the result is that the upper dishes do not get enough water and chemicals. It may also cause water to continue dripping onto dried dishes after the the drying cycle has stopped.
Repair Help & Product Troubleshooting for LG LDF6810 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our LG 6810 dishwasher has stopped cleaning. After the cycle the dishes are wet and covered in greasy clumps. We ran the test cycle and got the following: 3H/U3 11 22 33 44 55 66 04-2 32 33 0 (inlet valve) 35 36 37 38 23 (Thermistor) 3A 3A (beeped twice and showed 3A) 3A (beeped twice and showed 3A) Any advice you could give me would be appreciated. I have the service manual but have never done any type of dishwasher repair. I'd like to not have to replace this dis


1.) Take racks out of unit.2.) put both of the spray arms in the 12 o'clock position3.) Run the washer,once the washer has started wash cycle,open the door and ensure the spray arms have moved off of the 12 o'clock position. Write down re ... LG LDF6810 Built-in Dishwasher

Dishwasher shows several functions at once on keypad , but cant make any manual selections, press start, runs a short cycle 5 mins, beeps a long tone until i hit start again or shifts to other combo cycle then quits or beeps.


Shut the power off to the washer, see if it resets ... GE Dishwashers

Dishwasher has been stored. Was working fine-ish for first half dozen washes. Now not starting wash. From troubleshooting in manual I'm holding down first two buttons and it's saying "End", but keeps moving back to SOAK function (17 mins) and not doing anything. Display shows whole soak cycle to run, but on holding down start button it makes no difference - doesn't beep to acknowledge and start cycle.


After bringing the unit from storage did you conduct any service on it? Did you remove any water before storing the unit? when you store a unit like this you need to totally empty the unit from everything including wate ... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

Westoint Dishwasher I have looked in the manual under troubleshooting tips, but didn't find anything on the problem. The dishwasher goes into cycle,but during the wash cycle it stops,makes alarm and the wash and rinse ligts come on. And now I can't even find the product on this site.Westpoint Dishwasher WQP12-9240. Thankyou My dishwasher is stopping at stage 2 of the programme after beeping once. Quite often the detergent flap doesn't open. Am at my wits end and threatening to leave home!!!! Th


Hi again,\015\012\015\012That should be OK. Just get in touch with your sales rep or his boss. Somebody there will be able to look up the record of the purchase. If they ask for model & serial numbers, you have them. You will find ... Dishwashers

I have a maytag quiet series 300. When it is done with any of the cycles in leaves about 1-2 inches of water in the bottom of the dishwasher. I can manually hit the start button twice and it will go through a 2 minute cycle and pump out the water. I have cleaned the filter inside the dishwasher where it drains and have checked the hose to the disposal and it pumps out fine. It just doen't pump itself at the end of the cycle. HELP!


Here it is - Maytag Quiet Series 300 Manual ... Maytag Dishwashers

Bosch dishwasher My Bosch dishwasher finished a wash cycle and was showing the "END" light on, however, the motor was still running as though it was stuck on the drain cycle (there is a gurgling sound from where the eater drains off beneath the filter. Subsequently turning the washer on just repeats the apparent drain cycle with a constant gurgling sound (it does not kick into wash mode). The number on the manual is & 258 (7705).


Is all the water draining from the tub? if not the pressure switch will not reset and it will continue to try and clear it self...check drainage system.\015\0122. pressure switch is jammed on..build up in the sensing chamber..commo ... Bosch 24 in. SHU43 Built-in Dishwasher

Kenmore Elite - 9 Year old Dishwasher - A circuit blew and the dishwasher stopped in mid-cycle and did not drain.... I reset the circuit breaker and "manually" took the water out of the dishwasher. When I push buttons to restart the "95" shows up for the normal cycle. However, when I push start the "95" becomes a "--". Suggestions???


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

We have a Bosch SHX43C05UC/40 dishwasher. It did not come with a user manual and I cannot seem to find one online. The dishwasher is great in all aspects except I do not know how to disable the beeping alarm at the end of a cycle. It continues to beep for hours on end until the door is opened. Does anyone know how to disable the alarm? Thanks,


... Dishwashers

We have a Haier DW12-PFE2-U dishwasher thats 2 years old. The cycle stopped yesterday leaving an amount of water in the bottom and all of the program lights are illuminated with a recurring beeping sound happening. It says in the booklet that the drain hose is too high or bended. But its not. The display does show the time when a cycle is selcted but nothing happens. The dishwasher turns on and off normally. Can this problem be rectified? thanks!


Refer userr guide on page 21. It reads...\015\012\015\012When all the programme indicators " J" blink.\015\012Have you checked whether:\015\012the door is closed properly.\015\012\015\012 ... Dishwashers

My daughter accidentally turned on our GE GLDA690 dishwasher. I can't seem to cancel it out without actually starting the cycle. I opened the door before the cycle started but now it is sitting there beeping. The obvious thing is to load it with dishes and run it. But it is just the two of us and we don't really have a load full. Owner's manual is no help. Even turning off the circuit breaker will not stop this infernal beeping. How do I cancel it? Why isn't there a cancel button?


... GE GLDA690MWW / GLDA690MBB Built-in Dishwasher

DEC Dishwasher I have recently moved into a house we purchased and it has a DEC dishwasher model D-WQP12-DW SS but no manual. It was going threw a cycle then it all of a sudden stopped and starting beeping with the letters E4 flashing on the screen. We have tried turning it off and switching it bank on but the beeping continues and the letters keep flashing.


I have a manual if you still would like a copy ... Dishwashers

My Teka Dishwasher DW7 80 FI does the first water intake operation, it sounds like rinsing, and the you hear the pump evacuating the water and two beeps as when it finishes the complete cycle. About 6 minutes. Then Stops. The lights that stayed on says error E8 according to the manual. I have done the suggested fix as ending the cycle manually and turning off and on the DW. I tested "many" times in various modes and the same preemptive end.


Hi.E8 is alternate washing system malfunction.The alternate washing system consists of a valve located in the underside of the appliance and connected to the impeller motor. The valve opens and closes switching spray on and of ... Dishwashers

Service Manual Dear Sir, We are in the UK and although my double drawer dishwasher is branded Whirlpool ADG2900, I see that it is made by Fisher & Paykel. The top drawer motor started making a different noise about 3 months ago and now there is some dirty water left in the drawer after the cycle completes. The pots remain dirty. If you could get me the service manual I could try and sort it out. Please help! Thanks, RP.


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Recently there's been a white coating on dishes. Has to be scrubbed off manually or soaked in a vinegar/water solution. I flushed out the rotating arms to be sure water flows thru & it does. Checked bottom filter & basket...both clean. Twice used "finish" cleaner for dishwashers in the scrub cycle as directed. Turned off during drying cycle and now there is water across the bottom of the dishwasher. Next? Thanks for any help. Rosemary


Use any brand of dishwasher cleaner from a local store and run your dishwasher with it.I would also recommend that a calcium lime and scale remover be ran through your dishwasher to clean it out.\012this may have to be done a couple of times. ... Kenmore Dishwashers

My Bosch dishwasher is driving me crazy! When it finishes a wash cycle it beeps twice every 10 minutes until the door is opened. We can't run the dishwasher at night after dinner unless we're SURE we aren't going to bed before it's finished. We've tried every combination of button pushing and can't figure out how to disable the beeps. We'd be happy to permanently disable it if we have to. Help!


Hello there,\015\012\015\012It would help to know the model number of the dishwasher, but on many Bosch dishwashers, you can switch the cycle cycle completion signal off as follows:\015\012\015\0121. While holding the ... Bosch Dishwashers

Brand new Miele 2170/2180 dishwasher. First time we try to use it, it stops after a few minutes, the warning beep beeps incessantly, and all of the program lights are flashing. According to the manual, we should turn it off and on and then try again, which we did. The problem persisted. The manual says that this may indicate "a technical fault" and we should contact customer service. Unfortunately, they are closed for a three-day weekend. Any suggestions?


It is just possible you have a problem with the drain.if you plumbed the drain to a spigot on the sink trap, did you make sure the spigot is not blanked? the sink spigot will be blanked if it has not been used before to stop water from the sink ... Miele Dishwashers

*Beeping* thing Hobart SR-24 Dishwasher Beeps at me. Has beeped on startup since service tech was here last month...thought he fixed something we didnt even know was broken.....but now the thing beeps mulitple times a day...sometimes mulitple times in one cycle. What does it want?


... Hobart SR24-H Built-in Dishwasher

Miele Optima Series 2470 Dishwasher sounds a beeping sound and flashes a F19 error on the control panel. Last week the beeping sounded and flashed a F13 error on the control panel. I looked in the manual and it said to clean the filter, which I did and put it back in place and locked it. Now the beeps sound and it is now showing a F19 error on the control panel. Help!!


... Dishwashers

I have an Electrolux Dishlex DX303 Dishwasher. Recently it has been stopping early in the cycle and the display shows -10. The selected program is flashing. The cycle will restart by pressing the program button again but it no longers wash's right through the wash pe=rogram as it is meant to. I do not have the manual to trouble shoot and find out what this means. Your help would be appreciated. Regards Peter H


Hi peter,\012according to manual book -10 is not filling water fast enough.\012check inlet hose and valve, check pressure switch and pressure SW hose and clean sump filter which located bottom of tub that plastic strainer and stainless mesh clean the ... Dishwashers

Hi i have a Candy CDI 1012/B Intergrated dishwasher and 4 lights are flashing during the first programme then system drains and stops showing four lights lit. We have no instruction manual or service manual this would be good to get hold of as we have serveral of these machines. any idea what the problem is to save us time investigating it. Thanks Paul


Hi. The four leds flashing quickly at start of the cycle means that there is an inlet problem. Check that the inlet hose is not bent, blocked or kinked, ensure that water has sufficient pressure. The inlet valve can be tested reading Ohms at valve te ... Dishwashers

Our Bosch SGS 53E02 AU/30 Dishwasher has the Tap Light on all the time while the Dishwasher is filling up. It appears as though water cannot get through and takes a long time to fill. It also does not allow the wash cycle to start and the powder door does not open. Can you also get any Service manuals for this model?


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2119 seconds