Having problems with your Maytag 24 in. MDB9750AW Dishwasher ?

My dishwasher won't start (Series 300 purchased 14 months ago). The following lights are on: light wash,hi temp wash,sanitize, locked and the start /resume light is flashing put goes out when pushed and the machine does not start when closed. there has been an on going problem with the regular wash light not coming on when pushed.


Answers :

Hi\015\012
\015\012
It may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi Temp Scrub, energy saver dry. Now let the unit run for 2-3 minutes and then you press the Cancel/Drain button and allow it to completely drain and reset. If this doesn't work then it's an issue with the wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. You'll have to check the heater using a multimeter; the meter should read between 3000 to 3300 ohms (Use multimeter on Rx1 ohm setting). If heater is fine then make sure water pressure is optimum and fill valve is working fine. Hope this helps... Please post back for further assistance.
\015\012\015\012\015\012
\015\012
\015\012Daniel
Repair Help & Product Troubleshooting for Maytag 24 in. MDB9750AW Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher won't start (Series 300 purchased 14 months ago). The following lights are on: light wash,hi temp wash,sanitize, locked and the start /resume light is flashing put goes out when pushed and the machine does not start when closed. there has been an on going problem with the regular wash light not coming on when pushed.


Hi\015\012\015\012It may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting t ... Maytag 24 in. MDB9750AW Dishwasher

Matag MDBH940AWS dishwasher: Push start and light comes on but dw doesn't start - push again and light goes out but pump starts running but no water enters, push again , it shuts off ;; past problem never addresses is delay feature stopped working , no lights come on when delay buttons are pushed, so... control head in door replacement in order? Thanks , [email protected]


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

I have a Hotpoint Aquarius dishwasher (FDW60) The 3hr and 12hr lights are on and the machine won't respond to any other buttons pushed therefore I have not been able to reset the machine (that is if the delay start has actually been activated). It started with the machine not draining however I was able to drain it manually so that rules out any blockages. Please help...The manual doesn't have any troubleshooting advice for those lights... Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. When 3hr (Prewash) and 12hr (drying) light flashes it indicates\015\012the fault in the heating ci ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob


If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

Have whirlpool gold dishwasher made in Mexico, the control lock light stays on, when i push it and hold it just blinks three times and then stays on steady and then does the same over and over, before it did this I noticed the lights for different cycles flashing randomly, and even pushing cancel button once in a while would start the machine up....I have tried to unplug the machine and then plug back in, but nothing is helping....any ideas??


... Whirlpool Dishwashers

My Maytag MDB7609awb2 dishwasher has a glitch When I try to turn it on the heavy and light was lights go on but won't start the normal wash light won't go on at all until I keep pushing the off and on for a while, then suddenly the normal button works and start will start the machine, then is washes without any problem.


... Maytag 24 in. MDBH955AW Built-in Dishwasher

I have a Whirlpool ADF951, it has power to it and was working fine, the power light is on and the green light to the far right of the cycle lights is flashing, I can only get any response if I hold the start button in for about 10-15 seconds, The machine stops the light flashing and makes the noise like it is starting , that goes for about 20 secs then returns to the flashing light stage, any idea's please


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water tempera ... Dishwashers

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?


... Maytag Dishwashers

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

Quiet Partners III will not start. It blinks and then goes off. If I push the "Cancel" pad, it lights 2 and it attempots to drain (no water in tub) and then the light goes to 1 and within a minute it goe out.


Sounds like the anti flood activates when water (even a small amount) appears on the bottom of the machiene. This is usualy a leaking pipe but can also be caused by a clogged pipe. Most machiens do have a plastic pipe that (from the flat water tank) ... Dishwashers

The dishwasher does not start. Push the start button and the active light goes on but does not start. Light soon moves to clean.


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Dishwasher will not start. The clean light is flashing on and off. If I push the cancel button it appears to be draining but there is no water in the tub and it just continues. When I push the start button if flashes for a few seconds but then goes off. Thanks


Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:High te ... Kenmore 24 in. 16039 Built-in Dishwasher

After selecting wash cycle,I push start button. washing light comes on for a second then goes off.start light keeps on blinking. washing cycle would not start.


Check flood switch float is on(the float under the bottom rack)...also the switch under that...also you ca use a 110 volt test cord to test the inlet valve ... Dishwashers

Hi I have an F&P DW691 dishwasher (manufactured by whirlpool) the reser light is permanently giving two quick sucessive flashes and will not start the machine unless held on for 6 seconds, the machine then starts for a minute then stops and goes back to the two flash reset problem. Does any one know the fault code applications for this model.thanks Mike


Hi, I've got the same dishwasher but with a different fault, there's power down the cable to the d/w but no power lights on the front panel?Thanks. ... Fisher and Paykel Dishwashers

Nordmende dish washer model no. DWSN60WH . when power button is switched on machine gives a buzzing noise for about 10 seconds while the start button is still lighting. Noise stops and light goes off and then wash and end buttons start flashing continuely.


... Dishwashers

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

Machine goes through sequence when finished starts agaain with eco light flashing


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

The hidden control panel has only about half the lights showing what function is pressed. A couple of days ago the washer would not start. The only function which would work was the far left sensor light. After trying to cut power and pushing other buttons, to no avail, we let the machine sit a couple days. It now works again with only half the lights on function pad working. It acts like there was a electrical short.


First retrieve the tech spec sheet behind the toe-kick panel located near the floor and run the diagnostics if it will let you do so w/o the full operation of the keys on the pad,then if it wont the touchpad or keyboard on the front that you use to s ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Whirlpool ADG6962: The power light is flashing. When I push the power light and hold for a second, the machine seems to start it's drain cycle, but then stops and the power light continues to flash.


... Whirlpool Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

The power is on the machine but when the start button is pushed the light does not come on and none of the cycle will start.


Most common cause is a faulty door switch that will not let the machine operate. There is also a thermal fuse in the back beehind the rear panel that can blow and allow some power but not enough to operate the machine. ... Maytag Dishwashers

The control lock light goes on as soon as I press the cycle to start the dishwasher. The dishwasher does not start, presumably because the control lock stays on. I do not know how to disable the control lock function. Pushing and holding the button for 3 seconds does not disable it.


Hello &\015\012Welcome to FixYa\015\012\015\012To unlock the\015\012controls press and hold the HEATED DRY button for 20seconds. If the problme\015\012returns then only option is touch pad replacement. Please get back t ... Maytag Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0997 seconds