Having problems with your Miele 24 in. G646SC Plus Free-Standing Dishwasher ?

I HAVE A MIELE G646 SC DISH WASHER AND IT KEEPS LEAKING WATER INTO THE LOWER TRAY AND CUTTING OUT BECAUSE THE FLOOD SYSTEM KICKS IN.I HAVE THE MACHINE IN THE GARAGE WORKING UP ON TWO WORK MATE WITH THE UNDER TRAY OFF FOR THE FIRST FEW CYCLES THERE WAS NO LEAKING THEN WE FOUND IT LEAKING DOWN THE FILL PIPE.THE WATER IS LEAKING FROM AROUND THE AREA THE FILL PIPE FITS TO THE WATER SOFTNER BUT NOT ALL THE TIME.AN ENGINEER FROM MIELE SUGESTED IT COULD BE THE VENT INSIDE THE SIDE OF THE MACHINE BUT EV


Answers :

Have you made sure the water sofener filler neck locknut is tight to the bottom of the dishwasher?
i have had experience with one machine where spilled salt was not rinsed away after the softener was filled and this corroded a very small pin ***** sized hole near the filler neck
Repair Help & Product Troubleshooting for Miele 24 in. G646SC Plus Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAVE A MIELE G646 SC DISH WASHER AND IT KEEPS LEAKING WATER INTO THE LOWER TRAY AND CUTTING OUT BECAUSE THE FLOOD SYSTEM KICKS IN.I HAVE THE MACHINE IN THE GARAGE WORKING UP ON TWO WORK MATE WITH THE UNDER TRAY OFF FOR THE FIRST FEW CYCLES THERE WAS NO LEAKING THEN WE FOUND IT LEAKING DOWN THE FILL PIPE.THE WATER IS LEAKING FROM AROUND THE AREA THE FILL PIPE FITS TO THE WATER SOFTNER BUT NOT ALL THE TIME.AN ENGINEER FROM MIELE SUGESTED IT COULD BE THE VENT INSIDE THE SIDE OF THE MACHINE BUT EV


Have you made sure the water sofener filler neck locknut is tight to the bottom of the dishwasher?i have had experience with one machine where spilled salt was not rinsed away after the softener was filled and this corroded a very small pin *** ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


HERE I AM I LIKE THIS JOBE\015\012 PLEASE CHECK THE WATER INLET FILTER I FEEL FROM YOUR DESCRIBE IS IT\015\012 YOU NEED TO CLEAN IT BY ASMALL BRUSH >\015\012 THANKS ... Dishwashers

Bosch SMS4012GB dishwasher. Refused to fill. Found tray full of water in base of unit. Mopped up water about 2 litres. Machine works but lower reservoir on the side of the machine with float switch overfills and overflow leaks about an eggcup full each cycle. What is causing the overflow please?


An electric switch activated by air pressure. This device detects air pressure exerted on it through a flexible tube connecting it to part of a water tub. \015\012When activated, this switch then opens an e ... Dishwashers

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Hi _ We have a Stoves DW616 dishwasher which has started leaking water on filling from around the front door. The BGas engineer replaced the seals around the door with those from a Hygena which he said were the same and it worked fine for a few days and then a further deluge. He has now said there is a seal at the base of the door (just about invisible) and although he got a further Hygena seal this would not fit and he says that as it's obsolete the machine should be written off. Before I 'bin


... Dishwashers

I have a miele G646 dishwasher whihs has sprung a leak into the bottom tray. Have dried it up and reset float switch but the water seems to be coming from a pipe on the left hand side of the machine. i guess its a seal but which one and how would I replace it?


Hello,It sounds like the leak is coming from the water intake hose.The water intake house is located at the bottom sump of the dishwasher. To get to it the dishwasher has to be taken out and put on its back and the floor plan needs to com ... Miele Incognito G858SCVi Built-in Dishwasher

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Our Kemore dishwasher is leaking water onto floor, and the water valve continues to pour water when machine was turned off, but is not leaking water now. There is also standing water at bottom of tub from running machine last night. Can I test to see if it is fill valve or the overfill float? Are these easily replaced?


You just need to clean the pump area in the bottom of your unit :)try to take spray arm out if you can and then open pump cover clean it good but watch for broken glass in it ...and thats it :) ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

Miele dishwasher leaking around door area


... Dishwashers

GE Harmony top load washer: The soap tray when filled with liquid soap will not properly dispense the soap when the water is filling the machine and the soap tray remains full of water and soap at the end of the cycle?


Hi\015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allow the door to open. The stri ... Dishwashers

Dishwasher leaking Our dishwasher all of a sudden started leaking. I've taken the front panel off the door and can see exactly where. It's not a hole or anything...it's at the front, left edge of the basin, the bottom left corner at the front. It seems that right after it fills with water, it starts to leak once water is moving around inside and washing cycle starts. It is as if big waves are being pushed to the front left corner and over the lip of the basin. I don't think the water level is to


Just an idea...if i'm understanding you correctly,could the door seal be creased there or folded over by use and age to permit this to happen? cause you said nothing is missing ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri


... Bosch SHU9915UC Dishwasher

Miele 646 sc plus inlet tank solonoid valve on water tank leaking. We moved the machine from one room to another and now this valve is squirting out water. We replaced both door seals thinking that was the problem, then started the machine with a side pannel removed, and saw the jet of water coming from the solonoid valve on the water inlet tank. Any ideas.


... Miele Dishwashers

GE model GSD600003 repair manual: Before you answer this, please tell me if I will be charged for the answer, in case I'm not interested at this time. Do you have a diagram of the drain area and water inlet area? I took apart the plastic drain cover for cleaning because it was had pink mildew all around it where residual water pools. I cleaned it all up and put it back and now the dishwasher doesn't fill with water (none comes in). I'm just a guest trying to troubleshoot for relatives, so I'm


I'm not sure how mildew can grow in a dishwasher that is working well, but after cleaning it and putting things back together, it does now seem to be working. I thought that the water wasn't filling but I guess the heating element heats up before the ... GE Dishwashers

Smeg dishwasher my smeg dwf409 dishwasher pump keeps on running will not stop after washing cycle and there is water leaking from the bottom of it i can not see any leaks around the pump does the tray on the bottom always have water in it


My hotpoint dish washer aquarius is 4 years old leaves a sandy grit all over dishes water not spraying the top,done all the usual stuff run out of ideas ... Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Hi my bosch washing machine is leaking water from underneath, in fact when you turn the water tap on, it sounds like it is filling up, but the machine is not even plugged in.


Hello,Welcome to FixYa.Based on your description, " machine is leaking water from unde ... Bosch SHU9915UC Dishwasher

I have a Bosch SGS43A22 Dishwasher approx 8 years old. When I start a cycle it fills, runs for about 15 minutes, then drops out about a litre of water from the bottom of the door, then completes the cycle without any more leaking. I have run the machine with the front panel off and can see that water bypasses the top of the seal and fills the well of the seal then pours out. It only happens the once. The seal is fitted correctly. Any solutions?


After 8 years service the seal may have perished, so you should feel for a crack by stretching the rubber where you noticed the leak. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Miele dishwasher model# g868 could be 4 or u at end, customer complained water not coming into d/w ,when i got there water was coming in.for a few minutes then stopped filling ,drains fine, customer had not operated machine for a few days.i disconected the safety valve hose from under sink to see if water comes through does not when advancing cycle by hand, washes ok when water came in, thanks, Murray


... Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

I have a Kenmore Model 665.15955792 dishwasher. Water is leaking out the bottom of the door. I changed the door seal and the defusers but it continued. I took off the front of the door and I see the water filling into the base of the machine. When the dishwasher starts the cleam cycle, water is pushed up into the small square holes in the bottom of the door and then splashes up over the lip of the door and out onto the floor. It has never done this before, just started recently. I have had the d


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1235 seconds