Having problems with your Miele Optima G2430SCi Stainless Steel Built-in Dishwasher ?

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


Answers :

For a drainage fault heres what the miele service manual says for your machine
\015\012Water present in appliance and is not being drained off. The display shows

Drain fault F11. The buzzer is activated for 2 minutes.

Background information:
After each drain pump step, the circulation pump operates for 2 seconds and heater pressure switch B1/13 checks the water level. If it is too high (large quantity of residual water remaining in the cabinet), the drainage time is extended. If, after a further check, the water level is still too high, then the program is interrupted, the fault code is saved and the drain pump is activated. Fault code F11 is also registered if heater relay 1K1 is not activated after the fault code F51 register check; see Section 080-3.18. Drain hose kinked. Remedy: Check the drain hose for correct positioning. Cause: Drain blocked.

Remedy:

1. Clean the on-site drain.
2. Check the sump drain.
3. Check the filters.
4. Check the heater pressure switch and replace it if necessary.

Cause:
Ball in non-return valve in sump has not opened (e.g., jammed).

Remedy:
Clean the non-return valve in the sump or replace it if necessary. Cause: Foreign objects in the drain pump.

Remedy:
Clean the drain pump and its impeller.

Cause:
Drain pump defective.

Remedy:

1. Check the voltage supply to the drain pump.
2. If correct voltage is present, check the drain pump motor winding.
3. Replace the drain pump, if necessary.

Cause:
Foreign objects in heater pressure switch.

Remedy:
Check the heater pressure switch for blockages and correct switching point.

Cause:
Heater relay defective. Heater relay (coil or contacts) becomes defective during the drainage step (after fault code F51 register check).

Remedy:
Replace the heater relay.
\015\012there are two seperate water intake faults

Hi
\015\012\015\012

Intake/Drain light flashing means an issue while draining. The\015\012dishwasher is not draining properly. Please check for air gap on the dishwasher\015\012is not clogged. It prevents dishwasher from draining properly and sometimes the\015\012drain flow is restricted due to gunk. Cleaning or bypassing the air gap will\015\012resolve the issue. If this doesn't resolve the issue then it is due to seized\015\012(or stuck) drain pump. Keep handy large bowls and towels to soak the water out.\015\012Disconnect the power to the dishwasher or turn off the breaker to the\015\012dishwasher. Tip machine on its back; remove screws that hold the bottom tray\015\012on. Remove the hoses to the main motor, remove electrical connections and\015\012switch it on. If the error still appears then turn the rotary selector switch\015\012to "Stop/End" or press the "Start/Stop" switch for approx.\015\0125 secs to cancel the error message. Switch the appliance off and then back on\015\012again. Hope this helps...please post back for further assistance.
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

My Miele intake/drain light is flashing. It seems to be an intake problem, because water drains out fine, but seconds after water starts going to the machine, it stops and the intake/drain light starts flashing again. We've cleaned the filter in the inflow hose, cleaned the arms, and it still doesn't work. Any suggestions?


... Miele Touchtronic G892 Built-in Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

Viking pro dishwasher wont start/pump h20. previously cleaned out chunks of rust from feeder hose at valve under sink then it worked. light works, pumps out h2o ok. hearing clicking sounds from cycl control knob. can this part be replaced?


It sounds like you still have junk coming into the supply line. Consider running a new hot water line to thie dishwasher starting near the hot water tank. And yes, of course, each of these parts can be replaced. Joe ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

D1796 3-4 years old. Power on, lights flash, but when close door to start d/w, no noises made, water does not flow or anything. Water supply is on. Water valve to d/w open. Worked flawlessly until today.


Check the valve. maybe its a faulty valve.check the pump motor as well, this gives rise to the water. just wish that its not the circuit board because the circuit board costs a fortune.!\015\012\015\012if you say that its been used 3 to 4 ... Dishwashers

SHU4002UC/U06 the washer is not able to fill the hot water. I have checked the waster intake valve and hose. They are in good working conditons.


... Bosch Dishwashers

All of a sudden no water is running in my dishwasher. There is power and heat and the lights work. Have checked hoses and valves underneath sink and checked the float and dont see any problems there.


Hi,Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...Dishwasher ... Amana 24 in. ADB1500AWS Stainless Steel Dishwasher

Not getting enough water flow into the dishwasher, suspect that a filter is clogged due to recent work on the waterline in the kitchen sink. Need to know where the filter might be located (on the dishwasher or on the intake valve before the connection to the dishwasher hose)? Also would I need to disconnect the water supply to pull out the dishwasher for access to such a filter.


You didn't specify a brand but most dishwashers don't have a water "filter." They may have an inlet screen at the water valve, which is typically located under the dishwasher. Generally, the lower front panel will have to be removed and you should ... Dishwashers

Does not fill with water. Program light on. seems to click on ok but won't work further. Door closed ok Power ok water inlet on, checked for blockage on strainer in supply hose,filters and arms all clear.


Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012is with the water inlet valve that needs replacement. You can also test the\015\012valve before replacement, if the valve tests fine then the float switc ... Bosch Dishwashers

Bosch shv55mo3gb Keeps stopping during cycle, when open door the little tap light is on meaning trouble with water, checked supply vavle is on, checked filters and no kinks in hose, if i turn the water supply valve on and off then sometimes you can here the water flow through and it will work again, onlt 13 months old??


Use this link then click on insruction manual download type in the model number remember 0 is a number.I know that sounds condesending but i forgot. I used the manual with the ending aus.\015\012\015\012 ... Bosch 24 in. SHV55M03GB Built-In Dishwasher

Currently the only setting that is working is Sani Wash. If I use any of the other settings the Intake Drain light comes on and everythig stops. How can the Sani Wash cycle work fine and no Intake Drain light when all other cycles trigger the Intake Drain light and won't continue to wash? Thanks,Karen


I decided I'd wait for the repairman; I don't want to have to pay additional money. ... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

Short in door,touch control all light up when door is partially open,but goes out when door is closed and unit will not work. kitchenaid dishwasher.when door is open all lights are on for the cycle you press,but if you close the door the lights go out and dishwasher will not work


You have a broken wire in the harness that comes up through the door. It will be found by carefully moving individual wires till the symptom is duplicated. Not an easy thing when all the wires are tied together and moving one moves several. Been ther ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

Maytag MDBH985AWS...control panel button to turn on the washer does not work...wash cycle and delay lights will light when pushed but washer will not come on. Have tried pushing normal wash and heated dry in sequence, flipped circuit breaker, open and close door, pushed buttons while door is closed


... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

I have a Miele G892 SC dishwasher. When I start the cycle, it drains (except for a bit of water left below the triple filter). After that, the intake valve opens and water enters. It then does nothing for a period of time until the "intake/drain" indicator light starts flashing. When I open the unit, I find about 1/2in of water in the tub (above the tripe filter). I have 1. cleaned the intake valve filter (no blockage found) 2. Inspected the drain line at the base of the unit as well as t


The pump is running due to the float switch or the float itself either being stuck open or broken and showing a fault this is why you have water going in to a certain point but not the point required for washing the dishes and then due to the float s ... Miele Dishwashers

Some guys at the church was using this haracher 4000 psi, I was call and was told the machine stop working and would not crank up.I use a next machine to finish the charity jobs on saturday. Sunday the machine starts up but when I connect the garden hose and turn on the water it did not comes out, where the VALVE HOSE THAT GOES TO THE WAND ABOVE THE UPLOADER, I open every bolt and water comes out except the wand valve, pump was plush out and sprayed out, so we know that water enter the pump


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuc ... Karcher Pressure Washers

I have a Kitchenaid dishwasher model KUDV24SE. The "door open" light stays on. I have tested the switch on the door and it appears to be working. There is nothing blocking the door closing, the light just stays on which prevents the dishwasher from working. I am technically astute, just can't solve this problem (yet)..


... KitchenAid KUDS24SE Built-in Dishwasher

The dishwasher won't turn on to wash dishes when any buttons are pushed (quick wash, normal etc). However, other lights and buuttons work (drain, 1-2-3 buttons all light up). The door is closed and latches. Any ideas what I can do to make it work?


Probably the touch pad or may be called user interface. ... Whirlpool Dishwashers

Kitchen circut was accidently turned off. Now whirlpool gold disher will not work(unit was not running and the door was not closed all the way when circuit was turned off, All circuit breakers are on) There are no lights on display when door is closed completely, and it appears to have no power. Worked fine prior, what could it be? The unit has not been removed from under the counter yet. Is there a fuse or circuit breaker on the unit? If so where is it located? Other troubleshooting ideas


Hello- Turn power off. Remove kick panel and cover for power wires. Check connections. If these are ok, most likely suspect is a fuse at the control. This is a little harder to get to. Remove inside door panel screws. Unplug wires and remove panel. F ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

Unit won't pump out, checked the lower impeller and it was very loose, is there a drain valve on this unit? Model 587.14249991 The upper impeller is a fixed unit right to the motor but it appears the lower impeller is a push fit over a rubber sleeve. I only saewa check valve in the drain hose, is there any thing else I should check? hose is clear and the switch for the float is working ok.


At the bottom of the unit where the hose goes is a check valve. check to see if clogged. ... Dishwashers

The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again. It worked once then went back to all three light flashing. Before this, only the Normal Wash and Econo Wash lights were flashing.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I can't seem to access any previous post dialog that may have taken place but I'd like to help if you can fill me in on whats taken place to this point.\015\012\015\012The scenario you describe i ... Viking DFB450 Dishwasher

The water inlet valve dose not work, therefor the machin can not start. The inlet water signal light is off, however I checked the water pressure that was ok, also there is a noise in the valve. Is the valve is damaged???


Hello,Welcome to FixYa. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1408 seconds