Having problems with your Whirlpool 24 in. DU1100XTP Built-in Dishwasher ?

Du1145xtpba quietpartner II starts then stops shortly into cycle and the normal wash light just blinks, if you hit cancel then both lights will flash when unplugging/reconnecting ribbon cable from control board it will complete 1 cycle and more often than not will do the same thing

Answers :

Repair Help & Product Troubleshooting for Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Du1145xtpba quietpartner II starts then stops shortly into cycle and the normal wash light just blinks, if you hit cancel then both lights will flash when unplugging/reconnecting ribbon cable from control board it will complete 1 cycle and more often than not will do the same thing

... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons

... KitchenAid Dishwashers

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can

Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

I repalced a controller board and the Normal LED flashes and will not complete its cycle but a Light cycle will work ok.

Pl check the part no or the software version of the board. Contact the mfr with the model no and if possible the board no.Or refer to the new guide or ask for it mentioning the present board you just replaced. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

The unit is a Maytag model MDB5601AWW which it has recently began to lose power at the touch pad. The electrical breaker has been checked to confirm normal voltage. Additional investigation suggests that the unit can be reset by (1) disconnecting the power at the breaker, (2) disconnecting and reconnecting the ribbon cable that interfaces the touchpad with the control board. However, the problem reoccurs after a few normal wash cycles.

It sounds to me then that the display board or touchpad needs replacing,you havn't said that it's not doing it's cycles.so it's not causing any washing or cycle problems.i would replace the display board. ... Dishwashers

Recently replaced the control board for Electrolux EIDW6105GW1; after nearly a month of working w/o any problems this evening the machine made it through the wash cycle and then stopped working (all lights on wash cycle door menu are flashing). Took kick plate off bottom to check control board and the leak dectector is lit. I can see no leaks in front and am reluctant to do anything else with this POS. I spent nearly $1000 on this 18 months ago and have already sunk over $300 into a new contr

... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink

The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu

You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did

... Frigidaire FGHD2433KF Builtin Dishwasher

Maytag 24 in. MDB8951AWS intermittent button problems and incomplete wash cycle. The buttons work sometimes ... sometimes not. We also have experienced incomplete wash cycles when the buttons do let us start a cycle. Sometimes it completes correctly. Suspect control board, as I expect a membrane failure to cause incomplete cycle unless it is making a Stop/Cancel contact by itself. Can anyone chime in on thoughts?

... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi

... Hobart 24 in. LXIH-3 Built-in Dishwasher

Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher The lower drawer won't complete a cycle. It will fill and empty 4 or five times in succession then continue to wash for about 15 mins the it starts to fill and empty as before. On a 36 min Eco cycle after 1 hr it still shows to have 15 mins to the end of cycle and wants to run forever. I have swapped the control boards to no avail.

Http://www.retrevo.com/support/Fisher-&-Paykel-DD603-Dishwashers-manual/id/20093dj878/t/2/\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Lock on led keeps flashing. Can not cancel it, when pressed it also starts flashing. Control touch pad not functioning. When able to get going usually after turning off power for a while, it does not complete the cycle and the lock on led starts flashing again. Thanks

Hi,\015\012The flashing lock light problem might be caused by a stuck key on the touch panel console.If the control board detects that a key is stuck, then the dishwasher will suspend operation until the key is unstuck. If a key without a ... Dishwashers

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy

Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim

Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti

Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?

... Asko 24 in. 1585 Built-in Dishwasher

I have a kitchen aid dishwasher. Model KUDA03CTBS3. The unit shuts off before the second wash cycle begins. It does not complete the wash cycle. We replaced the control board already.

Hello, Welcome to FixYa. \015\012\015\012Sorry to hear about your on-going trouble. I would like to start by asking you a question in regards to this problem.\015\012\015\012When you state, "The unit shuts off before the secon ... Dishwashers


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012With the symptom you`ve described ( specifically the clean lite ) this is an error of poor water circulation or a heating fault...many times manifesting in th ... Whirlpool Dishwashers

Start and resume button flashes. Unit will not restart, cycle or cancel operation. Tried turning off electrical supply to re-boot control panel but that did nothing either. Is replacing the control board possible for a competent DYI-er?

... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

Bosch SHE43C05UC/22 Dishwasher cycles take 3-4 hours to complete. After cycle is complete, dishes do not dry and interior is not very hot (opening the door immediately after a cycle used to put you a

... Dishwashers

I have an Asko d3110. The normal wash setting is flashing, all of the other controls won't respond. The motor sounds as if its working but the cycle won't complete.

... Asko 24 in. D3112 Free-Standing Dishwasher

Bosch #SHE44C dishwasher does not fill. No power to the water solenoid, but power coming out of the control board and the emergency shut off float and switch is working. I need a manual with a wiring schematic and cycle sequence so I don't have to tear it completely apart to trace every wire. Thanks

... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a kitchen aid dishwasher model kudmo1tjbl0 and my problem is that sometimes I cannot start a cycle until I remove the ribbon attached to electronic control assemply and replug it to the board, then it will start. I have replanced th assembly back in November. Any ideas??

... Dishwashers

I have a Thermador dishwasher # dwhd650gfp with displayed error code 2, I verified oily residue on dishes and caked up grease on sump trap filter. This unit is 14 months old. I first reckognized that the dishes were not drying completely after cycle, then noticed the cold grease accumulation in drain area, then saw "E02" displayed on message board. I have read through some blogs that this issue could be a defective heater assembly, shorted or open circuit at the connection at the control pan

Hello,Welcome to FixYa. \015\012\015\012You would've been correct in your suspicion , of Bosch built dishwashers prior to this more recent revisions ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1076 seconds