Having problems with your Whirlpool 24 in. GU2500 XTP Built-in Dishwasher ?

Unit turns on but water does not fill the unit and yes water is on to the unit. What is my problem. Is it in the control panel or is there a float somewhere?


Answers :

Your problem is the flow Meter / Regen unit
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Unit turns on but water does not fill the unit and yes water is on to the unit. What is my problem. Is it in the control panel or is there a float somewhere?


Your problem is the flow Meter / Regen unit ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

FDB520RHS2 Dishwasher Same problem as posted. Dishwasher has power & water - control panel lights are on, when start is pressed the sound of a relay can be heard but nothing else happens - no water fill no cycle. Unit stays in this condition without running.


... Frigidaire FDB520RHS Full Console Dishwasher with 4 Wash Cycles 4 Wash Lev

Dishwasher (Model # SHU6806UC), unit is about 8 years old, very light use, less than once a month, and no previous problems. Turned on unit and after about 10 minutes, I found water on floor coming from dishwasher. Turned unit off and turned off water shut-off valve. Removed dishwasher from cabinet. Found mice had chewed a hole in water discharge hose under unit, inspected all hoses, and found another hole chewed in the 13" flex hose in the front of the unit. Also found the float chewed to alm


Hi,\015\012 Check the valve is open where the supply gets its water from the sink supply.There is a garden hose type swivel adapter after the valve, Close the valve tightly and then unscrew that hose coupling and see if the hose is full of w ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

GU2700 Whirlpool - Does NOT FILL 2 Gallons on INITAL FILL - unit has new parts FILL VALVE IS NEW OVER FILL SWITCH IS NEW while filling if you reach under the unit and push the over fill float up it turns off the fill cycle - if you let go - unit keeps filling - but does not add the correct 2 gallons - water is not even close to the heating element - does not have enough water to come out of the TOP SPRAY Arm


... Whirlpool Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

The start timer control cycles but nothing happens. The motor seems to gurgle while attempting to fill with water - but no water comes through. We have had this problem before and the repair person replaced the timer control board. Could this be the same problem reoccuring? I have also tapped and cleaned the water float as described by GE website.


I bought a new one and installed it myself. hardest part of installing was taking the old unit out. I compared the cost of a second repair of a 10 year old dishwasher vs. purchasing a new one. We also checked the pump and solenoid to find problems th ... GE Nautilus 24" Built-in Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Replaced the control panel on my indesit idl 700 because it was cracked, but still working. since then will not fill with water , water is on switches all seem ok but will not fill. three beeps can be heard , which means its asking for water, what is the problem ?


... Indesit 24 in. IDL700 Built-In Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

Whirlpool dishwasher g2p dws over filling thus filling bottom panel with water which in turn floats polystyrene disk which connects micro switch shutting off machine. also fills up over few days ? faulty fill valve may be ?


Could be but if it is filling up when it is not running then you have a bad solinoid ... Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Constant draining my candy cs445 17" is stuck on drain, it just sucks water out and wont stop. Turning the dial to stop does nothing, if i fill it with a sacepan of water it juts empties, and when all the waters gone its just keeps emptying, would a float switch be the problem or possibly a new dial ?


I would check the float.clean it up real good.make sure it moves freely.let me know ... Candy 17 in. CS455 Built-in Dishwasher

Hotpoint Dishwasher DWF 30, has power to the machine's switch on and off. The LED lights on control panel do not alluminate. There is no sound of pump working, or filling of water. all water ways are clear, impeller turns freely by hand. Any clues?


Just one question is the water to the unit turned on ? some times a unit will have a fail safe protection device where it would not start the system if there was no water pressure to prevent damage to the unit, but given the symptoms i really don't ... Hotpoint 24 in. DWF32P Free-standing Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

I have a pldb998cc0 frigidaire. The tech who came out told me the problem was the control panel and that they don't make them anymore. There is not apparent arc marks so it did not short out. We have turned it on and off to try to get it to reset and all that happens is the front panel lights all go on for 5 seconds then die out. There is no sound at all of pump or water. I talked to the manufacturer and they do not manufacture this part anymore. Any suggestions before I have to pitch it and go


As much as i love what i do i see so many bad techs this guy lied simple! the least he should have done was try another board if he was sure that was the fault he would have its simple electronics fault finding he must have at very least tested the b ... Frigidaire 24 in. PLDB999S Stainless Steel Built-in Dishwasher

I have a Kenmore model 15165 dishwasher. It suddenly stopped filling with water--no water comes into the machine at all. No exterior valves that could have gotten turned off. Is the problem with the float assembly?


... Kenmore 24 in. 15164 Built-in Dishwasher

Maytag diswasher MDB6600AWW Sprayer arms don't spin. Dishwasher makes all the right noises, except for spraying. Water fills properly and heats up. Water drains properly. Found paper on the back of access panel. Ran Manual Function and Field Service tests, no problems indicated. Disassembled all the pieces inside the bottom of the dishwasher. No obviously damaged parts. Shaft for motor turns freely. It seems like the parts that attach from the impeller to the motor shaft don't


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

I have a GE monogram zbd5900 that continues to drain, won't shut off. The drain pump just runs. None of the lights on the control panel will come on, tried pressing and holding buttons to clear, nothing. Turned off and on circuit breaker (even left it off overnight) and did not change. Drain is not blocked, pulled the unit out and put water in the bottom and it pumped the water out just fine. any thoughts?


See if you can access the tech sheet, should be on the right side of the underside of the unit after you remove the toe panel, or perhaps in the console. Almost sounds like a stuck key pad but the tech sheet might shed more information on this malf ... Dishwashers

Normal, light rinse and cancel button are blinking. Turned breaker on and off with no change. Took panel off and tech sheet to give the codes was not there so don't have it. Repairman with no tech sheet says need new control panel. Is there any way to get the tech sheet online to reset and see if problem persists. Kitchenaid kudu02fr The unit is 4 years old.


... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Water coming out front of dw at start of wash cycle. I leveled the unit. no luck. if you open the door during fill cycle the water does not shut off. also, may be a problem with float shut off working properly. what should I try next? Kenmore Elite 16579


Hi \015\012Check float to insure that it is free to move, it sounds like the dishwasher is over filling. That is assumed that you have not changed the type or amount of detergent being used.Also there is a probability tha ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1805 seconds