Having problems with your Whirlpool 24 in. GU940SCG Built-in Dishwasher ?

Dishwasher stopped without fully draining water after all cleaning seems to have completed, probably in rinse cycle. There is no power to the appliance, although breaker on panel is on. Any thoughts?


Answers :

If it is pluged into gfa plug it might be triped
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU940SCG Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher stopped without fully draining water after all cleaning seems to have completed, probably in rinse cycle. There is no power to the appliance, although breaker on panel is on. Any thoughts?


If it is pluged into gfa plug it might be triped ... Whirlpool 24 in. GU940SCG Built-in Dishwasher

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

Maytag quiet series 200 wont start, no lights on control panel,power is on, breaker tripped, flipped breaker back, other appliance on circuit works


... Dishwashers

Kenmore dishwasher My dishwasher stopped in the rinse cycle and no longer appears to be getting power, although the breaker works and the plug it is connected to is still receiving power. Is there a reset button for the motor, or some other idea to try and fix this? Thank you for your assistance. Mark


Mark, you probabley blew the thermal fuse located on the main board. Easy fix. Part number 8269213. You can ohm it out to be sure. You have to remove the inner panel to get at the control board. The fuse sits on the top side and clips on. Two wires ... Kenmore 24 in. 16293 Built-in Dishwasher

My kitchen aid dishwasher model # kudpo1flss3 stopped near the end of a cycle and now it is not responding or indicating power at the control panel. It has a little bit of water left in the tub but must have been close to completion as the dishes were clean. The breaker is on & there is power up to the connection @ the appliance. Almost acts like a main fuse is blown or something....


You will need to have the mains plug removed and the power cord traced up to the control panel which is the main program controller unit. It seems that the program controller has failed and if so the fuse would have blown with a reason m ... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Kenmore 665.1389 No power, lights won't come on. Tried circuit breaker didn't help. Is there a fuse or probably the control panel?


... Dishwashers

We have an Asco type DW 95.5 built-in, model 1885. During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric still runs. When I pop the circuit breaker, all is stopped. However, when power is restored, the lights and code flash as above, and, again, something electric runs. My email: [email protected] Thanks for any help...


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description " During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric s ... Asko Dishwashers

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Bosch APEXX model number SHY99A05UC/14 lost power. Power input line appears to have arced (white power line and wire nut show signs of stress). The power breaker did not throw at the junction box. Already cut back wire and re-attached new wire nut along with replacing the breaker at the junction box. Still no power. There are no other visible signs of power stress or water damage underneath the unit or inside the doo panel.


I do not have access to the user or service manual for this model.\015\012However, such symptoms could be result of heater element or thermal overload fuse blowing. Do you remember having a very hot dishwasher when the it lost power.\015 ... Bosch Dishwashers

GE Triton XL control panel suddenly went dark. Would appear the power is off but breaker tested ok and power verfied. I unpluged the unit for about 5 minutes. When I reconnected to power, 2 short beeps were heard but no lights on the panel are on. Any other ideas?


Hi\015\012\015\012 \015\012\015\012Thanks for using FixYa. From what you have\015\012described it seems that the control board has gone bad and should be replaced\015\012however, before replacing y ... GE Tritonr XL GSD6260JCC Dishwasher

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

Unit went dead. There is no power (electric) to it. I checked the circuit breaker and even changed the breaker, but no power. Removed the bottom foot panel and did not see any reset button. I don't know what else to look for.


The electronic control board has failed & needs to be replaced,by someone who knows what there doing.GOOD LUCKECO KIZZA ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

My Samsung DMR77LHS dishwasher has lost power completely near the end of a cycle. About an inch of water remains. I have power to the unit. I checked the 15 amp fuse in the unit - it had blown. I replaced it, but still no luck. The fuse is not blowing, but there is no power to panel. Nothing happens when you hit the power button - no lights or anything. Unit acts as if ther is no power at all. I have seen similar posts. Any thoughts?


Hi, whenever a fuse of that magnitude, or any fuse really, Blows, you should never just replace it, as to have any device, blow a fuse, trip a breaker, requires a major fault, they do NOT blow spontaneously ever. So you have had a major short circu ... Samsung DMR77LHS Tall Tub Dishwasher

No power I have no power.  I checked the plug and it had no power, so I reset the breaker.  Power returned to the control panel.  I selected normal wash.  It started up and 2 seconds later no power again.  Breaker flipped again.  What is the problem?


... Jenn-Air JDB7910 Dishwasher

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

My GE Dishwasher, Model GSD6960N10SS, has no power. None of the lights on the control panel are lit. The circuit breaker is on and the wall control switch is also on. I turned off the power for 30 seconds and turned it back on, but there is still no power.


... GE Dishwashers

An electrician switched off the power whilst doing other work. Power was restored OK. But when we came to use the dishwasher there appeared to be no power to it i.e the control panel remained blank. We have checked the fuse box and all appears to be in order.The appliance is a Siemens FD 8909 dishwasher


Maibe the internal fuse of the dishwasher blow for a spike, check first if you have power at the socket if so is highly posible that you have a blown fuse in the dishwasher ... Siemens Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

Our Dishwasher is not draining. We tried to run a test cycle and noticed there is no power. We checked the Electrical Panel and noticed that an unmarked breaker was tripped. We turned it on but still have no power. All other electrical items are working in the house. Is the power being cut off as a fail-safe function due to the water not draining? How do I fix the drain/pump? Please Help!


Hi,No, the water is a result of the dishwasher going off mid-cycle...Take the front kickplate off and see if you have power at the makeup box...you will need an electrical meter to check that...if there is power there then you have ... Dishwashers

I own a whirlpool gold model #GU980SCGQ3 . After the rinse cycle the dishwasher stopped . The water has not drained out and nothing on the control panel works when you press the buttons. The breaker did not blow on our main fuse panel in the house. Something similar happened a year after we bought it and the electrical panel had to be replaced under warranty. Is this the same problem? or something different?


... Whirlpool Dishwashers

No power to kenmore dishwasher control panel no lights on and flipped breaker still does not seem to get power


... Kenmore 24 in. 16032 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1230 seconds