Having problems with your Whirlpool Dishwashers ?

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


Answers :

I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing.
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

I have a KitchenAid dishwasher, model KUDP02FR. The "normal" cycle light is flashing. When I push "cancel" or "resume/start", they start flashing as well, but the dishwasher won't start. I turned off the power and turned it back on. The "normal" light still flashes, but when I press "resume" it all starts over again. Any ideas? I can't find this in the troubleshooting guide I have. Thanks.


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid KUDI01TBK Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

My bauknecht dishwasher gsi 4743 is not working. When I turn it to the program the start light is already blinking and when I press start the end light flashes and the pump appears to run for a few seconds and then the whole thing stops but the startt light continues to flash. If you could help, I would really appreciate it. Thanks!


... Bauknecht Dishwashers

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

Kitchenaid kudc03fvss0 dishwasher stopped mid cycle without drying dishes last week and then stopped altogether with lights flashing and full basin. I disassembled filter/pump cover in bottom and cleared several plastic pieces and cleaned chopping blade and screen. After unplugging/plugging and pressing cancel button the pump runs for about 10 seconds and stops with normal and heavy duty lights flashing. What should I check next?


... Dishwashers

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

When I press the on button the cycle light is on at the 50 degree setting and I cant change the setting and it wont run on that cycle. It has happened several times but this time it wont come around


Looks like micro controller problem. Contact authorized service center. ... Dishwashers

I have a Kenwood Slimline Dishwasher KS474s for a year and it has always worked near perfectly. rn However, over the last couple of weeks the dishwasher has not been running the cycles properly (stopping half way through etc, starting the the delay timer half way through cycle), but it always sorted itself after being turned off and starting again. The trouble is now it has got worse.. when I turn it on the panel and lights on the front just flash, the delay sometimes scrolls through on it'


... Kenwood Dishwashers

My Kitchen Aid Model KUDPO1FLSS5 dishwasher does not turn on. The lights all light up when selected. When I press start it used to blink all the lights and begin to run. Now, none of the lights blink and the cycle never starts.


... Dishwashers

Cycle wont run and lights on main washes flash


What is the best way change heater parts to a BF 162 dishwasher is it difficult or can some one change if they have a good under standing of machine ... Hotpoint 23 in. BFI62 Built-in Dishwasher

Touchpad--No Response The touch pad and Countdown timer display will NOT respond except when the Rinse Only pad is pressed. The Countdown timer displays "9" when this pad is pressed. As expected the light and display turn off after 30s. If after 30s or longer the Start/Cancel pad is pressed with the dishwasher door closed, then the Countdown timer displays "2H" and the dishwasher runs through the ?Auto Clean? or ?Heavy Wash? cycle. Not sure which since neither pad is lit. Is the problem the


The "2H" is an error code indicating the control panel needs to be replaced. ... Bosch 24 in. SHU53 Built-in Dishwasher

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

Frigidaire dishwasher Model GLD2250RD50: Stopped washing dishes when a ran the garburator full of water, panel lights of high temp and nearby started flashing, then I pressed cancel/start, lights went out the washer wont run, checked breaker no problem. door latched,


... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

My GE Quiet Power III dishwasher won't dispense the soap properly. It's all clumped up around the bottom. It won't run a full cycle.  When I turn it on it lights flash and it acts like it will run but then it stops.  


... Kenmore 24 in. 16032 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1917 seconds