Having problems with your Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher ?

It appears the two water arms are not turning.


Answers :

Hi,
\012


\012

I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and installed them in minutes...now the thing works like new... However I have also found that if the heating element goes bad then that also can mess things up bad... So I would buy new spray arms, and also check out the heating element to make sure it is working... Here is a tip that will help you with the online buying...
\012


Dishwasher
Spray Arms not Spinning

How to Buy
Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The
Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes

Repair Help & Product Troubleshooting for Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool dishwasher model number DU1055XTPQ4 that is not cleaning the dishes. When the dishwasher is working, the bottem arm is turning and water comes out the holes. The middle arm has some water coming out, but does not turn. The top arm does nothing. It appears I have a pressure problem. I took out all the arms and cleaned them, along with the plastic tube that feeds them water. They had some build up on them but not much. I have the same result as before. I took off the


... Whirlpool Dishwashers

It appears the two water arms are not turning.


Hi, \012\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and ins ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Kitchen Aid KUDS01FLSS2 dishwasher does not spray water thru the wash arms nor do they seem to turn. Additionally, one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" when rotated by hand. The spray arm assembly appears true on visual examination. The unit fills, cycles and pumps out in an apparent normal way. While on this site a while back I was advised to clean the unit and referred to a downloadable repair manual that was, in fact, not


Hi.The fact that "one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" would suggest a tubing problem. However there are more faults that will result in no spray. Testing in this case can be ... KitchenAid Dishwashers

The pump doesn't seem to put out enough water pressure to turn the various revolving heads/nozzles in the washer - all washing heads are operable (ie unblocked) while the S shaped nozzle at the base and the small round nozzle at the top/ceiling of the cabinet do revolve slightly or slowly - but the two main nozzles spout water but not enough to revolve Is this a defective pump or a partially blocked pump ? - or something else - I have checked everything else and they appear to be functioning


It will be helpful to know the make and model number of the dishwasher to diagnose the problem you have.\015\012\015\012Generally this is attributed to a blocked chopper assembly in the wash circuit but hard to be sure if your model has o ... Dishwashers

Dishwasher not working. Two weeks ago the heating cycle didn't switch itself off but appeared to correct itself. Now there is no water in the cycle... pump and heater working, just no water reaching the arms of the dishwasher. Any ideas why?


Sounds like a bad pump. If it drains the water and doesn't deliver at arms the pump is more than likely bad. First of all pull the water supply line off and see if there is build up from hard water on the in-line screen (if present), then If you are ... Whirlpool GU2400XTP Built-in Dishwasher

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.\015\012I wou ... Dishwashers

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

I have a mod. GSD2200G00WW . It has low water level and not enough pressure to turn the spray arm. When first starting i see water coming in but not enough. I added water in manually with a container and turned on and the spray arm rotated fine. I closed the door and turned back on and the water drained out of it instantly back to a low level. What now?


... GE Dishwashers

Top arm doesn't turn on Frigidaire fdb2415lfb0 it appears no water is comming out and there is a soap film on the dishes.


... Frigidaire Dishwashers

I just installed a new Kitchenaid dishwasher (Model KUDE60FVSS3). After filling with soap, closing the door and starting the machine, it fills with water, waits a couple of minutes and then I can hear low humming noices coming from down below. After opening the door it appears that neither spray arm has turned as if to wash. This dishwasher was purchased new a few years ago and kept in storage as our basement was being finished. This dishwasher has never completed one cycle. Any and all inf


If you have a garbage disposal, there is a plug in the dishwasher that has to be removed for the washer to drain. ... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

The impellers are not turning. We have checked the drain and it is clear. Water does come in and empties, but does not get sprayed around by the two impeller arms.


Hi lyst_diva,Firstly clean the spray arms, do this with small ear-buds & toothpicks. Clean the small holes at the edges. Clogged holes can be the reason why the spray arms aren't spinning anymore.If this is unsuccessful, it co ... Dishwashers

Maytag DWU9202AAB dishwasher upper spray arm not turning


... Dishwashers

Our KitchenAid whisper quiet model number kudp02crcs2 seems to have stopped filling?? or at least it does not spray any water and the arms do not turn...there is a very minimal amount of water in the very bottom and arms when we turn it on....it has also started to make a different low level sound..


... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

My LG dishwasher upper rack has stopped cleaning. The uppermost arm is seemingly getting no water at all and the arm on the underside of the upper rack is getting some water, but not enough to turn it. I have already disassembled and cleaned all the way down to the diverter assembly and it has not fixed the problem. I think this is a problem with a the (?) diverter pump or perhaps a sensor that sends water to the upper arms. I am trying to figure out how to further diagnose the problems. The


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDF6810 Built-in Dishwasher

No water delivered,or "spinning" of upper spray arm.Serviced @n year ago & worked very briefly. Spray arms & filter cleaned. Using a hose as water source to test.....spray arm isn't blocked. The problem appears to be water isn't being delivered to upper spray arms. What could cause this & how can I correct? Thanks for your time & response. Sincerely, Lee Ballard


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. If the dishwasher is not filling then it is w ... Avanti DW18 Built-in Dishwasher

I have a frigidaire dishwasher - model number PLDB998AC1. There are two spray arms in this dishwasher - lower and upper. The lower works fine but the upper spray arms are not spinning. There is what I think adequate water pressure coming in from the top but no movement on the upper spray arm. Here is what I know: 1) The water pressure and spray arms alternate between top and bottom. 2) The upper spray arm moves freely when I push it gently. 3) I have removed the pump and cleaned out an


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

The dishes in my dishwasher are not getting clean, particularly on the upper rack. It seems to be because the upper water arms are not spinning during the wash cycle. The bottom spin arm is working fine. I have cleaned out both upper arms as best as I could without removing them (above and attached below to the upper rack), as it does not appear that these arms are easily detachable. I am thinking maybe water is not making it up the line to the upper arms? I also have a lot of dirt in the b


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... GE Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

My Kitchenaid ModelKUDI01TJBL0 only leaks at initial start up. Just after the water fills, the first few seconds of the wash cycle. It pours out the front door for a couple seconds than no more for the rest of the wash. It is level, no cracked arms, or loose pumps.Splash guard is in place. The float seems to be working, not too much water in the bottom. I am stumped. Although I do feel that it has something to do with the level of the water being too high, when the arm starts turning, it makes a


Is the unit level or leaning back if leaning back it is morelikey filling too much if level make sure the float moves up/down easy if not clean ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

The dishwasher is not cleaning the dishes at all, so far I have done the following: Checked both sprayer arms and they move freely and do not appear to be clogged (I ran stiff wire thru holes in each The float is not stuck and moves up/down easily The water leavel in bottom of tub does appear to be low - so I added water filiing tub to heating coil - however this did not help and the water did not spray on lower or upper racks - this is an older model Kenmore Ultra Wash WHAT DO I NEED TO CHECK N


Heating element may have burned out. Check water temp during wash--should read between 130 to 140 F.If not the heating element,you may have to replace pump-motor assembly or wash impeller.Hope this helps. ... Kenmore Dishwashers

Baumatic BDW13 Problem with lower spray arm: arm is not being fed with water and is consequently not turning. (Note: top arm is turning as usual.) Might this be a problem with the recirculation motor? Any help most welcome! Jonathan Drennan


I think that you may be on the half wash setting, check to see if the light labeled as number 4 is on while washing, if it is, then you need to simple turn off this option. Let me know if it isn't. ... Baumatic 23 in. BDW13 Built-in Dishwasher

I have a Kenmore, Stock 15649, approximately 14 - 15 yrs old that worked fine until the past few days. The upper rack doesn't appear to be getting any water, as bowls and glasses are still dirty after being washed. It appears as though water would spray from the bottom, through a "nozzle" in the middle of the lower rack, then go to an arm located underneath the upper rack. I haven't noticed any obstructions in this path that would inhibit the water from spraying. Any suggestions (outsid


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1047 seconds