Having problems with your Zanussi 24 in. ZSF6150 Free-standing Dishwasher ?

I have a zanussi zdf 501. After a few minutes it freezes at .20 on the display. I don't think up to that point the cycles (all) are running properly

Answers :

I found that at 83 minutes my washer stopped. I found on examination that the powder dispenser had not opened, some granules had clogged the clip mechanism. I cleaned around it a bit and the next cycle the machine went right through. I checked, and this time the powder dispenser had opened. Hope this helps
Repair Help & Product Troubleshooting for Zanussi 24 in. ZSF6150 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a zanussi zdf 501. After a few minutes it freezes at .20 on the display. I don't think up to that point the cycles (all) are running properly

I found that at 83 minutes my washer stopped. I found on examination that the powder dispenser had not opened, some granules had clogged the clip mechanism. I cleaned around it a bit and the next cycle the machine went right through. I checked, and t ... Zanussi 24 in. ZSF6150 Free-standing Dishwasher

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr

Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

Asko d3250 i think dont have water presure because he take the water inside and then star the cycle and drain the water but i think the blades dont run i lisent a smal noise of water

First I would check the water line from the sink that is hooked up to the dishwasher.You may have a screen that plugged up.Also, if you have little pressure at your sink faucet, then you should check your house's water system. ... Asko 24 in. D3250 Built-in Dishwasher

My frigidaire dishwasher FDB1502RGC4 will not run a cycle. it will fill and drain the water but will not run a wash cycle. all the lights on the control panel lightup when they should. so i dont think it is a fuse. and there is not much i can see after i opened the front door, the control module and the console assembly. could it be one of these.

Having the same problem with mine, just replaced the discharge pump last week because it went out, worked a couple days now this. still have not figured out the problem ... Frigidaire FDB1502RGC Built-in Dishwasher

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to

While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

I have a Kenmore Ultra 15895 or 15891. It fills with water then doesn't run. It will continue through it's cycles, but stays full of water. If I hit cancel before it completes the cycle, the number 2 shows in the display and nothing happens. If I let it complete the wash cycle, it will sometimes start and wash properly.

HI. The culprit will be the main control sector. This control fault may possibly be corrected by initiating a hard reset. the logic chips are scrambled, and this damage may be correctable by simply unplugging, or shutting off the appropriate circuit ... Dishwashers

When using my Omega DW2006 dishwasher, the machine always displays that it has completed the wash cycle, when it has only done the pre rinse (after approx 12 minutes). Despite following the operating instructions religiously, I can't get it to run a proper wash cycle.

Hi,\015\012\015\012It seems that Motor pump has gone out. You need to replace the pump. In order to do this the unit needs to be pulled out so that you can access the pump. The sides of the dishwasher come off. \015\012Replace ... Dishwashers

Hi, I have a 3 year old Nemo F&P dishwasher which turns itself on and off for about 3 seconds each on/off continually.Eventually it does get enough water to wash but never goes into the wash cycle properly, ie the water just sits at the bottom. We dont think it's water pressure and it was working fine until recently.Could it be an electrical problem with the signal to fill properly not getting through? Thanks

Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing ... Fisher and Paykel Dishwashers

I have a Whirlpool GU2400XTPQ, it sometimes stalls with the display showing 44, it acts like it is running but when the door is open there is no water and it will not continue with the cycle from this point, you must restart the machine from the beginning of the cycle.

... Dishwashers

My Kenmore dishwasher model number 665-16389300 is starting to fill up and not drain during the normal wash cycle. Water will run out on the floor. When we hit cancel and drain it appears to drain just fine so I dont know if it is a pump issue or something in the cycle. What do you think?

... Kenmore Dishwashers

Good morning, I have a F&P dishdrawer ds605i (i think!) single drawer intergrated front. I dont know whats happened to it. The last cycle it decided not to empty the water out, so i manually emptied it. Now it seems stuck. All it does is run the fan. i can't start a new cycle. The start/pause button allows me to open and close the door as normal and i can hear the lid opening and closing.......... I have tried turning it off for a day at the wall switch. I have also noticed i can

Hi \015\012I guess the model no. you have sent is not correct,however given bellow are links from where you can troubleshoot your problem to your dishwasher which is related to your issue:-\015\012 ... Dishwashers

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that

... Kenmore 15912 Built-in Dishwasher

I have a Bosch Dishwasher, Model Number SHX46L, Serial Number 860200524 that is no working properly. After running a cycle, it did not pump out all of the water, though the water is very clear, and the dishwasher does not display that there is any electricity going to it. I have verified the is 120 Volts AC at the appliance junction box. However the dishwasher will not turn on, and no lights will come on? Do you have any suggestions? I would appreciate it if you would let me know what you

... Bosch SHX46L1xUC Dishwasher

My dishwasher Bosh Type S9G1B does not seems to load the water any more and the little water that is present is cold. The cycle run up to a point when the timer display jump up to a time longer than the original program time.

... Bosch Dishwashers

Bosch SHX33A: lights come on properly in response to buttons, it has power. Close door, it makes the normal startup sounds, then water flows in. Normally, at this point washer starts into normal cycle. Instead, it just sits there and nothing happens. Forever. Not a matter of patience: we've left it in that state all night long. Have flipped power circuit and started over, everything else I can think of to kick-start it, no change.

Hi\015\012\015\012The issue seems to be with the motor or the door latch\015\012assembly going bad and should be replaced. The washer won't start the cycle if\015\012motor is not working, as its filling with water so I believe that the do ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Unable to turn off the delay start and the latch is in the wrong position so that the door will not close properly. Also, there is no digital display--it remains dark. I tried the cancel/drain, which didn't help. The machine seems to be running through all cycles fine.

Pull the open handle to open the latch up and try to get it to close. Disconnect the power to the machine for a few minutes. Run a cycle that you don't usually run. See if that helps. ... Bosch 24 in. SHV66A03 Built-in Dishwasher

I have a Kenmore dishwasher model # 66513449K900 that will not stop running. I think it is stuck on the drain cycle. I can start the dishwasher on a cycle and it appears to clean the dishes, but after the cycle is complete, it continues running and running (on the drain cycle) until you open the door. What could this be?

It is possible that the machine does not move off the cycle because there are errors or back feedback from the inputs. For the program to end the main program controller must receive the feedback so as to switch off the circuit at the end o ... Dishwashers

My dishwasher runs 2 hours as a complete cycle. I think it is never going to finish but I have not stopped it in mid cycle. Dishes are very clean but they should when it runs this long. I hear it change cycles so I know it is not stuck on 1 cycle. It also makes a lot of noise. 2 hours of noise. HELP!!! How long it it suppose to run?

That means that the machine does not detect that one condition to continue the cycle is met.Sometimes\015\012 when this happen unesperience repairers replace the timer board , an \015\012expensive part that rarely fails. The timer b ... Whirlpool DU1055XTS Built-in Dishwasher

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!

I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?

I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

Dishwasher displays 888 on LCD and Cycles through settings on own

... GE 24 in. GLD6560LSS Stainless Steel Free-Standing Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.

... Whirlpool GU2400XTP Built-in Dishwasher

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke

... Craftsman Pressure Washers

I have a Bosch SHU5316UC dishwasher. The last two times it ran, my wife says the display said "CL" (for clean) after running through the cycle, but she heard a "motor running" until she opened the dishwasher. Attempting to run the dishwasher tonight, it won't start - it displays a "P" (error code?) when you attempt to start it. Can you tell me what the error code P is? Thanks, Dave

P stands for program in computer algorthms. The device displays program whenver chages were made to the default settings. A powered on devices least has malfunction only requires reseting to attaon default features. Depending on the type of device, r ... Bosch SHU5316UC Dishwasher

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about

Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1217 seconds